I am trying to create new files under my directory...but i getting the following message...
cat: write error: No space left on device
How do we handle this error.
I am not getting this error when I login as the super user (3 Replies)
hello all,
i have a proc binary that we run on unix environment, and it is generating this error
'' tstfile(): No space left on device ''
can you please assist on how to narrow down the problem?
thanks (4 Replies)
hi guys, me again ;)
i recently opened a thread about physical to zone migration.
My zone is mounted over a "bigger" LUN (500GB) and step is now to move the old files, from the physical server, to my zone.
We are talking about 22mio of files.
i used rsync to do that and every time at... (8 Replies)
Hi All,
This is Sandeep Gupta,
I am facing a problem with sudo command.
Whenever i am executing the command "visudo" i am getting the error "visudo: write error: No space left on device".
but i have checked on my Solaris Box everything is ok, i have enough free space on my box, and also... (13 Replies)
Hi,
We are trying to sort the 40GB file in unix and getting following error.
Error:
sort: can't write /var/tmp/stmAAAvsaGfJ.00002929: No space left on device
sort -t ',' -k4 $DIR/INF_ff_FULL.dat >>$DIR/Sort_INF_ff_FULL.dat; 2>$DIR/sort_error.log
Can you please advise how to... (2 Replies)
Hello people
I have a small fileserver running busybox (very small linux distro with most essential stuff on it) and I am trying to remove some unused directories on it.
When I try this:
rm -R test/I get:
rm: cannot remove 'test': No space left on devicedf shows:
Filesystem ... (8 Replies)
Hello,
I want to install GCC gcc-4.8.1-2.src.rpm for AIX 6.1
when I lance my command rpm -i gcc-4.8.1-2.src.rpm
I have this error
unpacking of archive failed on file gcc-4.8.1.tar.bz2: cpio: copy failed - No space left on device
I checked the free space and I am surpise becouse I have... (7 Replies)
Hi ,
In file first line start with "",when trying to remove using sed i am getting the below error .Please advise
sed -e 's///g' -e 's/$]//g' segment1.txt >>segment_m1
sed: couldn't write 1378 items to stdout: No space left on device
Thanks,
Mohan (1 Reply)
Hello all
posting here after scanning the net and tried most of the things offered
still no solution that worked
when I do :
$ df -h
Filesystem Size Used Avail Use% Mounted on
footmpfs 7.9G 60K 7.9G 1% /dev
tmpfs 7.9G 0 7.9G 0% /dev/shm
/dev/da1 ... (3 Replies)
Running a installation on Solaris 11 and getting error write to 1 failed
If anyone can advise ?
ORIGINAL_PATH="${PATH}"
# prepend /usr/xpg4/bin to PATH as needed
temporaryPath=`expr "${PATH}:" : '\(/usr/xpg4/bin:\)'`
if
then
PATH="/usr/xpg4/bin:${PATH}"
seem to have... (6 Replies)
Discussion started by: Mpumi
6 Replies
LEARN ABOUT XFREE86
pcitweak
PCITWEAK(1) General Commands Manual PCITWEAK(1)NAME
pcitweak - read/write PCI config space
SYNOPSIS
pcitweak -l
pcitweak -r PCI-ID [-b|-h] offset
pcitweak -w PCI-ID [-b|-h] offset value
DESCRIPTION
Pcitweak is a utility that can be used to examine or change registers in the PCI configuration space. On most platforms pcitweak can only
be run by the root user.
OPTIONS -l Probe the PCI buses and print a line for each detected device. Each line contains the bus location (bus:device:function), chip
vendor/device, card (subsystem) vendor/card, revision, class and header type. All values printed are in hexadecimal.
-r PCI-ID
Read the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in the form
bus:device:function, with each value in hexadecimal. By default, a 32-bit register is read.
-w PCI-ID
Write value to the PCI configuration space register at offset for the PCI device at bus location PCI-ID. PCI-ID should be given in
the form bus:device:function, with each value in hexadecimal. By default, a 32-bit register is written.
-b Read or write an 8-bit value (byte).
-h Read or write a 16-bit value (halfword).
SEE ALSO scanpci(1)AUTHORS
David Dawes (dawes@xfree86.org).
XFree86 Version 4.7.0 PCITWEAK(1)