03-11-2015
i know the output ;-) but you could look how long it takes to run every command, to find out, on which disks it stops or runs too long, and then analyze, what is wrong with the disks.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I know that free command displays memory usages however I like to know how the option and the results when I use this command..
PLease respond ASAP
thanx... I am a newbie.. :D (1 Reply)
Discussion started by: LiTo
1 Replies
2. UNIX for Advanced & Expert Users
Hi we are running a VIO server on a AIX p570
we cannot run and of the command the query the ODM
has anyone seen this problem or has a solution
the command just hangs. (1 Reply)
Discussion started by: truma1
1 Replies
3. Shell Programming and Scripting
I want to know wich hdisk have only one pvid and also display hdisk with two pvid.
hdisk1 00c3fcd4e516183f testvg active
hdisk2 00c3fcd4e516189b testvg active
hdisk3 00c3fcd4e51618ec testvg ... (1 Reply)
Discussion started by: khalidou13
1 Replies
4. Shell Programming and Scripting
I 've got this retourn when i tape the commande lspv:
hdisk0 00c3fce454950416 rootvg active
hdisk1 00c3fce454950416 rootvg active
I want to verify if hdisk0 et hdisk1 have the same pvid (ex : 00c3fce454950416)?
Can... (8 Replies)
Discussion started by: khalidou13
8 Replies
5. UNIX for Dummies Questions & Answers
All,
I have doubts related to free command in Linux.
My environment is RHEL5 - 64 bit OS
We have 2 node RAC database installed
Query output from node 1 is
Free -g
Total used free shared buffers cached
Mem: 32 25 7 0 5 15
-/+ buffers/cache: 4 27
Swap: 30 0 30
Query... (2 Replies)
Discussion started by: user7509
2 Replies
6. UNIX for Advanced & Expert Users
Hello, I need some help to interpret the below output...
What is -/+ buffers/cache?
My understanding is, total RAM is 3986152 Bytes, used RAM is 3950904 bytes.
What is buffers and cached?? Can any one please interpret this output? It would be great help if some one can help me on this?
... (2 Replies)
Discussion started by: govindts
2 Replies
7. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
8. AIX
Hi all,
When we run lpsv -free command on VIOS, it will take lot of time to display free disks i.e around 8 to 10 minutes. VIOS ioslevel is 2.2.1.4Can you have any solution for this problem?
Many Thanks (2 Replies)
Discussion started by: m_raheelahmed
2 Replies
9. Red Hat
Hi,
from below output.How to read or relate one marked in bold.
$ free -m
total used free shared buffers cached
Mem: 129176 92753 36423 0 2268 39973
-/+ buffers/cache: 50511 78664
Swap: 31996 ... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
10. AIX
Hi all,
when I issue a lspv <hdisk>, I get
TOTAL PPs: 7199 (1842944 megabytes)
When I issue a getconf DISK_SIZE /dev/<hdisk>, I get
1048576
Where do those additional ~800 GB come from the output of lspv.. anyone an idea?
The volume is an EMC LUN provided by a VIOS and... (2 Replies)
Discussion started by: zaxxon
2 Replies
LEARN ABOUT SUNOS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)