03-11-2015
Engineering call, I would suggest.
If you are dual power, check that it is actually getting it right up to the point where you plug the cables into the PDU or at least the back of the machine if there is an internal cable that then plugs in the front (depending how it is built for engineering access)
If you have dual service processors, can you tell with ASMI if they are both working? You should have separate physical connections too.
I found this with the POST codes. It's a bit of a monster at 300 pages, but it might help you get to sleep.
Problem Determination and Service Guide for the IBM Power PS701 and PS702 (8406-71Y)
I hope it is relevant to your server in some way.
Robin
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, i was installing solaris 8 on sunfire v250 and the power fails :mad: , now it does not boot from cd rom and get the next msg:
ð
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 512 MB memory installed, Serial #56338483.
Ethernet address 0:3:ba:5b:a8:33, Host ID: 835ba833.
... (1 Reply)
Discussion started by: agustincm
1 Replies
2. Solaris
hi guys,
i'm new so don't bite too hard.
having a problem booting up a V210 running sol9 on after a power outage...
an init5 was done but not a init0 before the power cut... so now when booting up it gives the ff:
SC Alert: Host System has Reset
Probing system devices
Probing memory... (2 Replies)
Discussion started by: lungsta
2 Replies
3. SCO
After System power get failed
File system is not getting mounted in read- write mode (1 Reply)
Discussion started by: gtkpmbpl
1 Replies
4. AIX
We have a RS6000, model B50, type 7046, where I installed AIX 4.3.3
But, if the power goes off, the operating system does not restart,
and I have to go there and push the button to start AIX again.
Is there any way this procedure to be avoided,
this is, I want the AIX to start automatically... (9 Replies)
Discussion started by: sebastia.net
9 Replies
5. AIX
i am new to aix environment and all my servers are @ remote location
just curious to know , what issues/tasks we will be facing when there is a power outage in a data centre, i heard outage's will be a challenging task for administrators.. any example of that sort will be a great help (2 Replies)
Discussion started by: rigin
2 Replies
6. Linux
Hi guys,
I was wondering if you could share some of your knowledge, in the event of a power outage.
Let presume you are on duty and you get a call at midnight because half of your cabinets have no power, air conditioning is down and you deal with a ton of 500 error messages on your boxes.
... (9 Replies)
Discussion started by: TECK
9 Replies
7. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
8. Solaris
Hi all, this is my first question on this forum, so if it isn't in the correct location, please let me know where to post.
We are using Solaris 8 and with the power setting enabled the monitor will not wake up. It can take anywhere from 5 to 30 minutes for the monitor to display.
One of the... (3 Replies)
Discussion started by: Wrongway
3 Replies
9. AIX
Hi everyone,
We had a power outage few days ago, and I got the servers up and running but I was informed to look into, if there is a way to bring up the servers automatically/defaultly.
I was told the windows admin has their server set up where the servers are up automatically if there is a... (11 Replies)
Discussion started by: Adnans2k
11 Replies
10. AIX
A team member installed the wrong version of License Code on a Power 740 system used in our Development environment.
The system will no longer boot.
Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
Discussion started by: kevinedailey
1 Replies
LEARN ABOUT OSX
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)