re: your new code - while this link is for Power7 - the meaning of the code has not changed -> IBM Knowledge Center ignore the page title - it is the frame you want!
Basically, is says "Perform isolation procedure FSPSPC1"
So, after searching around a bit I found this area of interest for you: IBM Knowledge Center again - ignore the page title - it is the frame you want!
More searching finds this page:
IBM Knowledge Center likewise - ignore the page title - it is the frame you want!
with this text
The quick text is - FSP (Full Service Processor) needs a reset after a Power Failure. Worst case is you will need to reinstall the firmware.
Been there - done this!
And I am providing the links - because when you do not know what you need to find - you will not see it when it stares at you.
Good Luck!
Last edited by MichaelFelt; 03-11-2015 at 07:46 AM..
Reason: although the apparent title is the same - each link is very different. The frame, not the pagetitle is the key.
Hi, i was installing solaris 8 on sunfire v250 and the power fails :mad: , now it does not boot from cd rom and get the next msg:
ð
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 512 MB memory installed, Serial #56338483.
Ethernet address 0:3:ba:5b:a8:33, Host ID: 835ba833.
... (1 Reply)
hi guys,
i'm new so don't bite too hard.
having a problem booting up a V210 running sol9 on after a power outage...
an init5 was done but not a init0 before the power cut... so now when booting up it gives the ff:
SC Alert: Host System has Reset
Probing system devices
Probing memory... (2 Replies)
We have a RS6000, model B50, type 7046, where I installed AIX 4.3.3
But, if the power goes off, the operating system does not restart,
and I have to go there and push the button to start AIX again.
Is there any way this procedure to be avoided,
this is, I want the AIX to start automatically... (9 Replies)
i am new to aix environment and all my servers are @ remote location
just curious to know , what issues/tasks we will be facing when there is a power outage in a data centre, i heard outage's will be a challenging task for administrators.. any example of that sort will be a great help (2 Replies)
Hi guys,
I was wondering if you could share some of your knowledge, in the event of a power outage.
Let presume you are on duty and you get a call at midnight because half of your cabinets have no power, air conditioning is down and you deal with a ton of 500 error messages on your boxes.
... (9 Replies)
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Hi all, this is my first question on this forum, so if it isn't in the correct location, please let me know where to post.
We are using Solaris 8 and with the power setting enabled the monitor will not wake up. It can take anywhere from 5 to 30 minutes for the monitor to display.
One of the... (3 Replies)
Hi everyone,
We had a power outage few days ago, and I got the servers up and running but I was informed to look into, if there is a way to bring up the servers automatically/defaultly.
I was told the windows admin has their server set up where the servers are up automatically if there is a... (11 Replies)
A team member installed the wrong version of License Code on a Power 740 system used in our Development environment.
The system will no longer boot.
Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)