03-05-2015
Do you think the firmware password comes from the nvram being set to defaults? Is there any mention of a default password?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up.
Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
7. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
8. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
ESP(4) BSD Kernel Interfaces Manual ESP(4)
NAME
esp -- Qlogic FEPS and FAS366 SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device esp
HARDWARE
The esp driver provides support for the Qlogic FAS216 and FAS408 SCSI controller chips found in a wide variety of systems and peripheral
boards. This includes the Qlogic SCSI cards found in most Sun Ultra 1e and Ultra 2 machines.
For Qlogic PCI SCSI host adapters, the isp(4) driver should be used in place of the esp driver.
IMPLEMENTATION NOTES
During the boot sequence, the esp driver searches the linked list for LUN info by LUN ID. At this point the driver will attach on that
instance, and then attempt to attach every sub-device.
There are at least 4 variations of the configuration 3 register. A second config register must be loaded to inquire the chip revision, oth-
erwise the ncr53c9x_reset() function will not set the defaults correctly.
The drive attach routine attempts to set the appropriate bit to put the chip into Fast SCSI mode so that it does not have to be figured out
each time. This will then be stored in the NCR registers for later use.
The esp driver makes use of the LSI 64854 DMA engine which contains three independent channels designed to interface with an NCR539X SCSI
controller; an AM7990 Ethernet controller; and certain types of parallel port hardware. As such this driver may eventually replace the
amd(4) driver for network hardware.
DIAGNOSTICS
The following driver specific error messages may be reported:
esp: cannot map %d segments The device was unable to map segments while mapping the SCSI devices in DMA mode.
unknown variant %d, devices not attached An unknown version of the card was found and devices will not be attached.
Unhandled function code %d The device returned a function code which the driver is unable to handle, most likely during negotiation.
esp:%d:%d: selection failed %d left in FIFO The target left the command phase prematurely. If a command did not reach the device then it
will be reported as shown above.
invalid state: %d The device has reached an invalid state.
SEE ALSO
amd(4), isp(4), scbus(4), camcontrol(8)
http://www.qlc.com/
http://www.sun.com/
HISTORY
The esp driver was written for NetBSD by Eric S. Hvozda. The esp driver was then ported to FreeBSD 5.3 by Scott Long <scottl@FreeBSD.org>.
AUTHORS
This manual page was written by Tom Rhodes <trhodes@FreeBSD.org> instead of porting the original from NetBSD.
BUGS
The esp driver includes the sbus front-end but lacks the PCI front-end. Thus it can only support the FEPS/FAS366 SCSI found in Sun Ultra 1e
and Ultra 2 machines at this time.
This driver should eventually replace the amd(4) driver, but that requires porting the PCI front-end mentioned above.
BSD
September 18, 2005 BSD