Sponsored Content
Full Discussion: Sun Sparc Ultra 30 help
Special Forums Hardware Sun Sparc Ultra 30 help Post 302937334 by robbo007 on Thursday 5th of March 2015 05:31:34 AM
Old 03-05-2015
Do you think the firmware password comes from the nvram being set to defaults? Is there any mention of a default password?
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Sun Ultra sparc 60

Hello everybody!! I need your help again. I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp. "windu_sm_o aaaa,baaa,caaa,daaa" etc. I am not able to locate which application is generating these files. Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies

2. UNIX for Advanced & Expert Users

Need Help , Ultra SPARC can not loading

Dear All, I have trouble, I have SPARC Machine and when start for loading, can not finish ! this is copy off message from my system Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard OpenBoot 3.31, 512 MB memory installed, Serial #12116535. Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies

3. Solaris

ultra sparc 2 no video - ok prompt access

I have an ultra sparc 2 with no video - I connect to it with hyperterm. Is there a way to get to the OK prompt? I have tried control/break and that does not work. If not is there a video card I can get to put in this box? I have Solaris 10 installed on this machine. Thanks (7 Replies)
Discussion started by: tribbles
7 Replies

4. Solaris

In Sparc Ultra 45 machine, how to enable bge1

In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up. Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies

5. Solaris

Null modem cable in Ultra sparc 10

Hi Gurus, Can I use null modem cable in Ultra sparc 10 workstation Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies

6. Debian

Problem installing Debian5 on an ultra sparc machine

Comments/Problems: Machine boots from CDROM, starts SILO Version 1.4.13, display welcome message (welcome to Debian GNU/Linux lenny! built on 20081218-10:06 ). boot: Allocated 8 Megs of memory at 0x40000000 for kernel Loaded kernel version 2.6.26 Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies

7. Solaris

How much better performance is ultra SPARC IV+ 1.95GHz than 1.35GHz?

Dear Guru, My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?. I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies

8. Solaris

Sun Sparc Ultra 4 won't boot - disk errors

Hi all. I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'. I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies

9. Solaris

How to install PGX32 on Sparc 10 Ultra?

I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10. I've got the Oracle installation guide for it and I got as far as: "4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive." I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies

10. UNIX for Beginners Questions & Answers

Start /SYS on SUN SPARC does not start machine [SUN SPARC ENTERPRISE T-5240]

-> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS ]-> show HOST /HOST Targets: bootmode diag domain Properties: autorestart = reset autorunonerror = false bootfailrecovery = poweroff ... (29 Replies)
Discussion started by: z_haseeb
29 Replies
yppasswd(1yp)															     yppasswd(1yp)

Name
       yppasswd - change password in yellow pages (YP) service.

Syntax
       yppasswd [ name ]

Description
       The  command lets you change your password in the yellow pages (YP) map, a network data base service.  Only you or the superuser can change
       your YP password.

       When you enter the command, the program prompts you for the old password and then for the new password. Note that  the  passwords  are  not
       displayed on the screen.

       Next,  the  program asks you for the new password again, to verify that you have typed it correctly.  If you do not type the passwords cor-
       rectly, you will receive an error message after you enter the new password.

       Your new YP password must meet one of the following requirements:

	  o It must be a combination of at least six alphanumeric characters, or

	  o It must be a minimum of four characters, with at least one being non-alphanumeric, such as a control sequence.
       The command does not change the YP password.  This command only changes the local password file and not the YP master password  file.   See
       Chapter 3 of the Guide to the Yellow Pages Service for further information.

Diagnostics
       Please use a longer password
       Your new password does not meet the minimum length requirement.

       Mismatch- password unchanged
       You misspelled your new password or its verification.

       couldn't change passwd
       Your new password can not be activated. It must be different from your old password and your login name.

Files
       Password file

       Yellow Pages directory

See Also
       passwd(1), passwd(5yp), ypfiles(5yp), yppasswdd(8yp)
       Guide to the Yellow Pages Service

																     yppasswd(1yp)
All times are GMT -4. The time now is 02:42 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy