03-04-2015
Sun Sparc Ultra 30 help
Hi all,
I managed to salvage form work an old Sun Sparc Ultra 30. I have had it stored (controlled storage) for a few years and decided to get it home and boot it up.
It starts up with a beep then I can hear disks spinning up, CDROM moving but nothing is displayed on the monitor.
Can anyone help me troubleshooting what is failing?
Many thanks.
---------- Post updated at 01:20 AM ---------- Previous update was at 12:13 AM ----------
right.. I've managed to get video. I unscrewed the PSU and disconnected the small connector on the motherboard in order to check the ram. But I could not work out how to remove the ram and clean it. I then booted again and now shows...
---------- Post updated at 01:21 AM ---------- Previous update was at 01:20 AM ----------
It asks for a firmware password which I don't have
Any ideas?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello everybody!!
I need your help again.
I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp.
"windu_sm_o aaaa,baaa,caaa,daaa" etc.
I am not able to locate which application is generating these files.
Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies
2. UNIX for Advanced & Expert Users
Dear All,
I have trouble, I have SPARC Machine and when start for loading, can not finish !
this is copy off message from my system
Netra t 1120/1125 (UltraSPARC-II 440MHz), No Keyboard
OpenBoot 3.31, 512 MB memory installed, Serial #12116535.
Ethernet address 8:0:20:b8:e2:37, Host ID:... (4 Replies)
Discussion started by: heru_90
4 Replies
3. Solaris
I have an ultra sparc 2 with no video - I connect to it with hyperterm.
Is there a way to get to the OK prompt? I have tried control/break and that does not work.
If not is there a video card I can get to put in this box?
I have Solaris 10 installed on this machine.
Thanks (7 Replies)
Discussion started by: tribbles
7 Replies
4. Solaris
In Sparc Ultra 45 machine, how to enable bge1 port, how to do if bge0 is down then bge1 should automatically up.
Thanks & Regards (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
5. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
6. Debian
Comments/Problems:
Machine boots from CDROM, starts SILO Version 1.4.13,
display welcome message (welcome to Debian GNU/Linux lenny!
built on 20081218-10:06 ).
boot:
Allocated 8 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.26
Loading initial ramdisk... (3 Replies)
Discussion started by: mtk
3 Replies
7. Solaris
Dear Guru,
My boss has a plan to upgrade cpu of server so he needs to know how much better performance(percentage) is Ultra SPARC IV+ 1.95 GHz than Ultra SPARC IV 1.35 GHz?.
I am looking for documentation to reference but I didn't see anything close to my point. If who know,... (3 Replies)
Discussion started by: unitipon
3 Replies
8. Solaris
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Discussion started by: jamie_collins
3 Replies
9. Solaris
I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10.
I've got the Oracle installation guide for it and I got as far as:
"4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive."
I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT SUSE
set_color
set_color(1) fish set_color(1)
NAME
set_color - set_color - set the terminal color
set_color - set the terminal color
Synopsis
set_color [-v --version] [-h --help] [-b --background COLOR] [COLOR]
Description
Change the foreground and/or background color of the terminal. COLOR is one of black, red, green, brown, yellow, blue, magenta, purple,
cyan, white and normal.
o -b, --background Set the background color
o -c, --print-colors Prints a list of all valid color names
o -h, --help Display help message and exit
o -o, --bold Set bold or extra bright mode
o -u, --underline Set underlined mode
o -v, --version Display version and exit
Calling set_color normal will set the terminal color to whatever is the default color of the terminal.
Some terminals use the --bold escape sequence to switch to a brighter color set. On such terminals, set_color white will result in a grey
font color, while set_color --bold white will result in a white font color.
Not all terminal emulators support all these features. This is not a bug in set_color but a missing feature in the terminal emulator.
set_color uses the terminfo database to look up how to change terminal colors on whatever terminal is in use. Some systems have old and
incomplete terminfo databases, and may lack color information for terminals that support it. Download and install the latest version of
ncurses and recompile fish against it in order to fix this issue.
Version 1.23.1 Sun Jan 8 2012 set_color(1)