Hi,
I have a large file with a repeating pattern in it. Now i want the file split into the block of patterns with a specified no. of lines in each file.
i.e. The file is like
1...
2...
2...
3...
1...
2...
3...
1...
2...
2...
2...
2...
2...
3...
where 1 is the start of the block... (5 Replies)
Dear all,
I have a large file which is composed of 8000 frames, what i would like to do is split the file into 8000 single files names file.pdb.1, file.pdb.2 etc etc
each frame in the large file is seperated by a "ENDMDL" flag so my thinking is to use this flag a a point to split the files... (4 Replies)
I have a few txt files in some directory and I need to check their sizes one by one. If any of them are greater than 5mb then I need to split the file in two.
Can someone help?
Thanks. (6 Replies)
Hi Friends,
Below is my requirement. I have a file with the below structure.
0001A1....
0001B1..
....
0001L1
0002A1
0002B1
......
0002L1
..
the first 4 characters are the sequence numbers for a record, A record will start with A1 and end with L1 with same sequence number. Now the... (2 Replies)
Hello, I have a large file (2GB) that I would like to split based on pattern and size.
I've used the following command to split the file (token is "HELLO")
awk '/HELLO/{i++}{print > "file"i}' input.txt
and the output is similar to the following (i included filesize in KB):
10 ... (2 Replies)
I need to split a file if it is over 2GB in size (or any size), preferably split on the lines. I have figured out how to get the file size using awk, and I can split the file based on the number of lines (which I got with wc -l) but I can't figure out how to connect them together in the script.
... (6 Replies)
Hi ,
I have huge files around 400 mb, which has clob data and have diffeent scenarios:
I am trying to pass scenario number as parameter and and get required modified file based on the scenario number and criteria.
Scenario 1:
file name : scenario_1.txt
... (2 Replies)
i have file1.txt
asdas|csada|130310|0423|A1|canberra
sdasd|sfdsf|130426|2328|A1|sydney
Expected output : on eaceh third and fourth colum, split into each two characters
asdas|csada|13|03|10|04|23|A1|canberra
sdasd|sfdsf|13|04|26|23|28|A1|sydney (10 Replies)
I have to split a file based on number of lines and the below command works fine:
split -l 2 Inputfile -d OutputfileMy input file contains header, detail and trailor info as below:
H
D
D
D
D
TMy split files for the above command contains:
First File:
H
DSecond File:
... (11 Replies)
Hi,
I have a directory in Unix and there are folders available in the directory.
Files are created on different month and now i have a requirement to calculate size of the folder on month basis.
Is there any Unix command to check this please??
Thanks (6 Replies)
Discussion started by: Nivas
6 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)