02-05-2015
Quote:
Originally Posted by
jlliagre
You should tell the disks capacity and what is the intended usage of the pool.
Bartus suggestion will provide the best performance while a raidz will give you 50% more storage. Both will sustain a full disk failure.
300G per disk and the pool hosts log files for a Netback server.
10 More Discussions You Might Find Interesting
1. Solaris
I had a pool which was exported and due to some issues on my SAN i was never able to import it again. Can anyone tell me how can i destroy the exported pool to free up the LUN. I tried to create a new pool on the same pool but it gives me following error
# zpool create emcpool4 emcpower0c... (0 Replies)
Discussion started by: fugitive
0 Replies
2. Solaris
I am not seeing anyway to remove a LUN from a Zpool...
Am I missing something? or do i have to destroy the zpool and recreate it? (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
3. Red Hat
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Discussion started by: bobby320
2 Replies
4. AIX
Hi
I have one of the disk missing in my NIMVG. My doubt is can I remove this hdisk2 online ? few of the file systems seems to be spread over 7 PV's. that's why i'm worried. Can someone suggest if I can replace this disk online. Also how to check if there is some data present in hdisk2 alone... (2 Replies)
Discussion started by: newtoaixos
2 Replies
5. Solaris
Hi ,
One of my zone went down and when i booted it up i could see the pool in degraded state with some check sum errors . we have brought the pool online after scrubbing. But few files are showing this error
Bad exchange descriptor
Please let me know how to remove these files (2 Replies)
Discussion started by: chidori
2 Replies
6. Solaris
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
Discussion started by: general_lee
2 Replies
7. AIX
Dear All,
I created a new partition through "Integrated Virtualization Manager" but there have an error when I added a new disk to the partition. The disk already created without any issue,
Below error is to add the disk to the partition
An error occured while modifying the assignments... (5 Replies)
Discussion started by: lckdanny
5 Replies
8. Solaris
Hello,
I need some help in recovering ZFS pool. Here is scenerio. There are two disks -
c0t0d0 - This is good disk. I cloned it from other server and boot server from this disk.
c0t1d0 - This is original disk of this server, having errors. I am able to mount it on /mnt. So that I can copy... (1 Reply)
Discussion started by: solaris_1977
1 Replies
9. Solaris
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
10. Solaris
On an OmniOS server, I removed a single-disk pool I was using for testing.
Now, when I run zpool import it will show it as FAULTED, since that single disk not available anymore.
# zpool import
pool: fido
id: 7452075738474086658
state: FAULTED
status: The pool was last... (11 Replies)
Discussion started by: priyadarshan
11 Replies
LEARN ABOUT DEBIAN
dpm-addpool
DPM-ADDPOOL(1) DPM Administrator Commands DPM-ADDPOOL(1)
NAME
dpm-addpool - define a new disk pool
SYNOPSIS
dpm-addpool --poolname pool_name --def_filesize defsize [ --def_lifetime def_lifetime ] [ --def_pintime defpintime ] [ --gc_start_thresh
perc ] [ --gc_stop_thresh perc ] [ --gid pool_gids ] [ --group pool_groups ] [ --help ] [ --max_lifetime max_lifetime ] [ --max_pintime
maxpintime ] [ --ret_policy retention_policy ] [ --s_type space_type ]
DESCRIPTION
dpm-addpool defines a new disk pool.
This command requires ADMIN privilege.
OPTIONS
pool_name
specifies the disk pool name. It must be at most CA_MAXPOOLNAMELEN characters long.
defsize
specifies the default amount of space reserved for a file. This is by default in bytes, but the number may also be post-fixed with
'k', 'M' or 'G' for kilobyte, Megabyte and Gigabyte respectively.
def_lifetime
specifies the default time a space or volatile file is kept in the system (in seconds).
defpintime
specifies the default time a file is kept on a given disk (in seconds).
gc_start_thresh
specifies the minimum free space in the pool. If the percentage of free space goes below this value, the garbage collector is
started. Default is 0.
gc_stop_thresh
specifies the percentage of free space in the pool above which the garbage collector is stopped. Default is 0.
max_lifetime
specifies the maximum time a space or volatile file is kept in the system (in seconds).
maxpintime
specifies the maximum time a file is kept on a given disk (in seconds).
pool_gids
if not zero, the disk pool is restricted to this comma separated list of group gids.
pool_groups
if set and not "ALL", the disk pool is restricted to this comma separated list of group names.
retention_policy
specifies the retention policy supported by the disk pool. It can be R (for Replica), O (for Output) or C (for Custodial). Default
is R.
space_type
indicates the type of space supported in the disk pool. It can be V (for Volatile), D (for Durable), P (for Permanent) or - (to
accept any type). The latter is the default.
EXAMPLE
dpm-addpool --poolname Volatile --def_filesize 200M --s_type V
EXIT STATUS
This program returns 0 if the operation was successful or >0 if the operation failed.
SEE ALSO
dpm(1), dpm_addpool(3)
LCG
$Date: 2010-02-05 10:50:58 +0100 (Fri, 05 Feb 2010) $ DPM-ADDPOOL(1)