02-03-2015
If you audit file creation, you will have events from specified user.
Around the same timestamp it would generate file creation and executed command with parameters passed (other class).
I haven't tested this of course but i figure it is like that.
Question is what is the actual requirement of audit, what information on what incident do you need ?
Try talking to the folks to refine/define the requirements of audit, be more specific etc.
Hope that helps
Regards
Peasant.
10 More Discussions You Might Find Interesting
1. Solaris
Hi All,
Any one has, sun solaris audit program which covers everything one need to check as a security auditor.
Audit Program will help.
Thanks,
Ghanshyam
Emails not allowed - see the Rules (4 Replies)
Discussion started by: ghanshyampatel
4 Replies
2. Solaris
How do I know that audit is enabled in soalris. in AIX 'audit query' command gives me the info whether auditing is on or not.
Raghav (1 Reply)
Discussion started by: raghavender_sri
1 Replies
3. Solaris
can you please share what you use to audit what files are deleted, when files are deleted and who deleted them?
thx (1 Reply)
Discussion started by: melanie_pfefer
1 Replies
4. Solaris
I just want to audit and log to syslog when a user is added, removed or modified from the system.
According to the docs I have:
#/etc/security/audit_control
dir:/var/audit
flags:ua
minfree:20
naflags:ua
plugin:name=audit_syslog.so.1; p_flags=ua
But neither syslog nor auditreduce -c ua... (7 Replies)
Discussion started by: glisha
7 Replies
5. Solaris
Hi Friends
I am a Solaries newbie and I am looking out for a software or command or config that can capture all commands run by all users on a server on a daily basis. I believe that this Audit is being done in almost all enterprises and would like to know how the same is done there.
Any... (3 Replies)
Discussion started by: Hari_Ganesh
3 Replies
6. Solaris
cron audit problem. job failed
I’m getting problem with crontab in Solaris 8
Crontab stop and is not running for all the cron jobs
under cat /var/cron/log
> CMD: /var/sh/go.sh
> root 24835 c Sun Sep 26 08:06:00 2010
< root 24835 c Sun Sep 26 08:06:00 2010 rc=1
! cron audit problem.... (5 Replies)
Discussion started by: Mr.AIX
5 Replies
7. Solaris
Dear All,
I have one of my Servers, running Solaris 9. I wanna enable the Audit log enabling, the way I did in Solaris 10 Servers.
After running, the bsmconv script, giving the reboots, modifying all the audit files in /etc/security, the audit is enabled, but the audit file which shall be... (3 Replies)
Discussion started by: sumeet1806
3 Replies
8. Solaris
Does anyone know if there is software written to view the audit logs generated by Solaris? I am referring the the logs created by auditd. It produces an unreadable log. I am familiar with auditreduce and praudit, but I am looking for something that produces a report, much like logwatch looks at the... (4 Replies)
Discussion started by: brownwrap
4 Replies
9. Solaris
Linux audits in syslog, any time a user is deleted or added. However, I'm running a Solaris11 VM, and find no such entries. How can I enable auditing for useradd and userdel? Oracle's documentation on managing the auditing service, has been of no assistance. Thanks.
Customizing What Is... (7 Replies)
Discussion started by: Nvizn
7 Replies
10. Solaris
hi,
I enabled bsm modules (/etc/security/bsmconv) and rebooted Solaris 10. But service is going into maintenance state. I rebooted server and I see one error saying "sys/c2audit:audit_kssl() not defined properly". I am not sure, what it is indicating and how it should be fixed. Please suggest, how... (5 Replies)
Discussion started by: solaris_1977
5 Replies
audit(1M) audit(1M)
NAME
audit - control the behavior of the audit daemon
SYNOPSIS
audit -n | -s | -t | -v [path]
The audit command is the system administrator's interface to maintaining the audit trail. The audit daemon can be notified to read the con-
tents of the audit_control(4) file and re-initialize the current audit directory to the first directory listed in the audit_control file or
to open a new audit file in the current audit directory specified in the audit_control file, as last read by the audit daemon. Reading
audit_control also causes the minfree and plugin configuration lines to be re-read and reset within auditd. The audit daemon can also be
signaled to close the audit trail and disable auditing.
-n Notify the audit daemon to close the current audit file and open a new audit file in the current audit directory.
-s Notify the audit daemon to read the audit control file. The audit daemon stores the information internally. If the audit daemon is
not running but audit has been enabled by means of bsmconv(1M), the audit daemon is started.
-t Direct the audit daemon to close the current audit trail file, disable auditing, and die. Use -s to restart auditing.
-v path Verify the syntax for the audit control file stored in path. The audit command displays an approval message or outputs specific
error messages for each error found.
The audit command will exit with 0 upon success and a positive integer upon failure.
/etc/security/audit_user
/etc/security/audit_control
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Stability |Evolving |
+-----------------------------+-----------------------------+
bsmconv(1M), praudit(1M), audit(2), audit_control(4), audit_user(4), attributes(5)
The functionality described in this man page is available only if the Basic Security Module (BSM) has been enabled. See bsmconv(1M) for
more information.
The audit command does not modify a process's preselection mask. It functions are limited to the following:
o affects which audit directories are used for audit data storage;
o specifies the minimum free space setting;
o resets the parameters supplied by means of the plugin directive.
For the -s option, audit validates the audit_control syntax and displays an error message if a syntax error is found. If a syntax error
message is displayed, the audit daemon does not re-read audit_control. Because audit_control is processed at boot time, the -v option is
provided to allow syntax checking of an edited copy of audit_control. Using -v, audit exits with 0 if the syntax is correct; otherwise, it
returns a positive integer.
The -v option can be used in any zone, but the -t, -s, and -n options are valid only in local zones and, then, only if the perzone audit
policy is set. See auditd(1M) and auditconfig(1M) for per-zone audit configuration.
25 May 2004 audit(1M)