Hello !
I have a result of ls command in a file:
file1 file2 file3.out file4.pdf file5
they all are separated by space.
I need to put them on a separate line
example:
file1
file2
file3.out
file4.pdf
fil35
i tried
sed 's/ /\n/g' inputfile > outputfile
but did not help (3 Replies)
Hi,
I need convert a dump file in the following format : (please note that line numbers are provided for easy look)
Original file:
1 2007-10-2482.90 No trade 0 0.00 100000.00
2 100000.00
3 0.00
4 HOLD
5 2007-10-2589.75 Bought 1114 1114 100000.00 0.00
... (5 Replies)
cat file.txt
fvnuiehuewf
ruevhxncvkjrh
zxjvurhfuwe
jkhvBEGINvfnvf
ijrgioe
Trying to delete a line that has the pattern "BEGIN"
cat sedtest
filename=file.txt
pattern=BEGIN
sed "/^$pattern/d" "$filename" (9 Replies)
Hi
Is it possible to do the following in a single command
/usr/xpg4/bin/sed -e '/rows selected/d' /aemu/CALLAUTO/callauto.txt > /aemu/CALLAUTO/callautonew.txt
/usr/xpg4/bin/sed -e '/^$/d' /aemu/CALLAUTO/callautonew.txt > /aemu/CALLAUTO/callauto_new.txt
exit (1 Reply)
I've been trying this, and can't get it right. I want to put a line break before a word, but only if it's *not* the last word in the line. So if the break work was "fish," then...
We want to fish tomorrow
...would become...
We want to
fish tomorrow
...but this line would remain... (3 Replies)
Hi there,
I'd like to delete the beginning of a line up until it finds a certain word or character string: in this case, I'd like to delete each line up to the word "mounting".
Thanks ;)
Susan (12 Replies)
Hi,
I have gone through may posts and dint find exact solution for my requirement.
I have file which consists below data and same file have lot of other data.
<MAPPING DESCRIPTION ='' ISVALID ='YES' NAME='m_TASK_UPDATE' OBJECTVERSION ='1'>
<MAPPING DESCRIPTION ='' ISVALID ='NO'... (11 Replies)
I have a file from which I am trying to delete a particular word on a particular line.
NEW
NEW
/v/engine
NEW
/ifs/list
NEW
/ifs/vdrome
NEW
I am trying to delete the first line only if it contains the word NEW. I am also trying to delete the last line only if it contains the word NEW. I... (11 Replies)
Hi all,
I ahve a program which has to delete a line in a file... if i run the sed command through shell prompt it works fine. But if run it using code its throwing error. May i know where i am doing wrong.
the file has 3 lines
# cat /root/.ssh/known_hosts... (4 Replies)
Hi,
I have a shell script which has a for loop that scans list of files and do find and replace few variables using sed command. While doing this, it deletes the last line of all input file which is something wrong. how to fix this. please suggest. When i add an empty line in all my input file,... (5 Replies)
Discussion started by: rbalaj16
5 Replies
LEARN ABOUT V7
vp
VP(4) Kernel Interfaces Manual VP(4)NAME
vp - Versatec printer-plotter
DESCRIPTION
Vp0 is the interface to a Versatec D1200A printer-plotter with a Versatec C-PDP11(DMA) controller. Ordinarily bytes written on it are
interpreted as ASCII characters and printed. As a printer, it writes 64 lines of 132 characters each on 11 by 8.5 inch paper. Only some
of the ASCII control characters are interpreted.
NL performs the usual new-line function, i.e. spaces up the paper and resets to the left margin. It is ignored however following a CR
which ends a non-empty line.
CR is ignored if the current line is empty but is otherwise like NL.
FF resets to the left margin and then to the top of the next page.
EOT resets to the left margin, advances 8 inches, and then performs a FF.
The ioctl(2) system call may be used to change the mode of the device. Only the first word of the 3-word argument structure is used. The
bits mean:
0400 Enter simultaneous print/plot mode.
0200 Enter plot mode.
0100 Enter print mode (default on open).
040 Send remote terminate.
020 Send remote form-feed.
010 Send remote EOT.
04 Send remote clear.
02 Send remote reset.
On open a reset, clear, and form-feed are performed automatically. Notice that the mode bits are not encoded, so that it is required that
exactly one be set.
In plot mode each byte is interpreted as 8 bits of which the high-order is plotted to the left; a `1' leaves a visible dot. A full line of
dots is produced by 264 bytes; lines are terminated only by count or by a remote terminate function. There are 200 dots per inch both ver-
tically and horizontally.
When simultaneous print-plot mode is entered exactly one line of characters, terminated by NL, CR, or the remote terminate function, should
be written. Then the device enters plot mode and at least 20 lines of plotting bytes should be sent. As the line of characters (which is
20 dots high) is printed, the plotting bytes overlay the characters. Notice that it is impossible to print characters on baselines that
differ by fewer than 20 dot-lines.
In print mode lines may be terminated either with an appropriate ASCII character or by using the remote terminate function.
FILES
/dev/vp0
SEE ALSO opr(1)VP(4)