No, its not a movie, its a command to get you from the sc> ALOM prompt back to the console or ok prompt.
You must log into the ALOM, then to jump back to the console enter "console -f".
Problem is that this leaves you logged in on the ALOM.
Question: is there an escape key sequence to get... (1 Reply)
Hi guys,
I'm in trouble with a Sunfire T2000.
The OS (Solaris10) is up and running, but I can't log in the sc>I think the terminal server is crashed!
Does anyone know if I can reset the sc> from the OS?
How can I do that?
Thx (6 Replies)
Hi Everyone.
What is the differece b/n ALOM and ALOM CMT Service processor.
I am trying reset ALOM login/passwd using scadm utility on T2000, while I am googling I came cross ALOM CMT doesnt support scadm utility, but ALOM supports.
Not sure how different are these.
Thanks, (0 Replies)
I have a few servers that are all having the same problem when trying to login to their ALOMs. The are T2000's. When I go to login I get the login prompt, but some machines ALOMs aren't responding to the initial login:
# ssh xx.xx.xx.xx
Copyright 2008 Sun Microsystems, Inc. All rights... (9 Replies)
Hi gurus,
I have a sun netra 240 server. I want to get to the ALOM but it always ask for login and password. Can anyone tell me how I can reset the ALOM it to default so I can be able to configure it?
Thanks lots. (2 Replies)
Hello forum,
I have a SUN v250 at home that I have to practice Solaris. I currently have Solaris 9 installed and the ALOM Sun(tm) Advanced Lights Out Manager 1.5.2.
From the ALOM I want to access the console.
sc> console -f
Enter #. to return to ALOM.
after that there is no response.... (19 Replies)
Hi guys,
I'm new with solaris.
I just received sunfire T2000 server.
Problem:
ALOM keep hang/stuck/jammed.
Steps do before it hang :
1. Connect to T2000 (using RJ45 - DB9 cable)
2. Open putty, connect via serial.
3. Power on the server.
4. Its loading.
5. then, hang.
... (1 Reply)
Hi all,
I have some problems with the fan FT0.F0, which looks like has a problem with the PROM/ALOM ( I am nor sure who).....but, in fact, the fan is working properly even in other V440 Sparc Server.
We checked HW comunication between Fan and the MotherBoard, and we think is a problem of... (8 Replies)
Discussion started by: proof_enrique
8 Replies
LEARN ABOUT FREEBSD
color.4th
COLOR.4TH(8) BSD System Manager's Manual COLOR.4TH(8)NAME
color.4th -- FreeBSD color-detection boot module
DESCRIPTION
The file that goes by the name of color.4th is a set of commands designed to simplify color logic. The commands of color.4th by themselves
are not enough for most uses. Please refer to the examples below for the most common situations, and to loader(8) for additional commands.
Before using any of the commands provided in color.4th, it must be included through the command:
include color.4th
This line is present in /boot/loader.4th file, so it is not needed (and should not be re-issued) in a normal setup.
The commands provided by it are:
loader_color? Returns FALSE if the loader_color environment variable is set to ``NO'' (case-insensitive) or ``0''. Otherwise
returns TRUE (unless booting serial).
The environment variables that effect its behavior are:
loader_color
If set to ``NO'' (case-insensitive) or ``0'', causes loader_color? to return FALSE, indicating to many modules that color
should not be used.
FILES
/boot/loader The loader(8).
/boot/color.4th color.4th itself.
/boot/loader.rc loader(8) bootstrapping script.
EXAMPLES
Standard i386 /boot/loader.rc:
Use color where applicable:
loader_color="YES"
SEE ALSO loader.conf(5), loader(8), loader.4th(8)HISTORY
The color.4th set of commands first appeared in FreeBSD 9.0.
AUTHORS
The color.4th set of commands was written by Devin Teske <dteske@FreeBSD.org>.
BSD August 6, 2013 BSD