01-22-2015
If you know an address that would route through that card, just try a simple ping. It should re-plumb into when the switch is available again. It might be worth checking that the card and switch port agree on speed and other settings.
You might also get some useful information from entstat naming the device in question, e.g. entstat -d en1
I hope that this helps,
Robin
9 More Discussions You Might Find Interesting
1. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
2. AIX
Hello Gurus,
I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access??
1. netstat -Aan | grep <port... (1 Reply)
Discussion started by: tenderfoot
1 Replies
3. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
8. UNIX for Advanced & Expert Users
Hello all,
I need your help with any command to release a port on AIX.
Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies
9. AIX
Hello,
I have some doubt about the NIC device on my AIX box.
When using lsdev command
/ > lsdev -Cc adapter | grep en
ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2... (11 Replies)
Discussion started by: Phat
11 Replies
LEARN ABOUT DEBIAN
rsuplnk
RSUPLNK(8) Linux Programmer's Manual RSUPLNK(8)
NAME
rsuplnk - User entry into the ROSE network.
SYNOPSIS
rsuplnk [-q] <port>
DESCRIPTION
The rsuplnk program allows a user to gain entry into the ROSE network using the standard pseudo-digipeating method. Recent Linux kernels
are aware of this form of operation and the ax25d program can listen for such connections. The normal mode of operation of a ROSE switch is
to have one ROSE address (ie port) per physical AX.25 port. Therefore ROSE users coming in on a given AX.25 port will appear as if they
come from the associated ROSE port. This is the reason for the need for a ROSE port as an argument.
To use rsuplnk you need an entry in ax25d.conf to listen for incoming connections. In the example below, I will be listening for ROSE con-
nections on my AX.25 port 144 using the callsign KE4GAJ-10 and the ROSE port associated with the AX.25 port is rs144.
#
[KE4GAJ-10* VIA 144]
NOCALL * * * * * * L
default * * * * * * - root /usr/sbin/rsuplnk rsuplnk rs144
#
There would typically be one rsuplnk per user access AX.25 port. The associated program for exiting a ROSE network is rsdwnlnk.
All errors generated by rsuplnk are written to the system debug log file.
OPTIONS
-q Supresses the messages generated by rsuplnk when making the connection.
FILES
/etc/ax25/rsports
SEE ALSO
rose(4), ax25d.conf(5), ax25d(8), rsdwnlnk(8), rose_call(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 29 April 1997 RSUPLNK(8)