01-22-2015
If you know an address that would route through that card, just try a simple ping. It should re-plumb into when the switch is available again. It might be worth checking that the card and switch port agree on speed and other settings.
You might also get some useful information from entstat naming the device in question, e.g. entstat -d en1
I hope that this helps,
Robin
9 More Discussions You Might Find Interesting
1. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
2. AIX
Hello Gurus,
I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access??
1. netstat -Aan | grep <port... (1 Reply)
Discussion started by: tenderfoot
1 Replies
3. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
8. UNIX for Advanced & Expert Users
Hello all,
I need your help with any command to release a port on AIX.
Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies
9. AIX
Hello,
I have some doubt about the NIC device on my AIX box.
When using lsdev command
/ > lsdev -Cc adapter | grep en
ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2... (11 Replies)
Discussion started by: Phat
11 Replies
IY(4) BSD Kernel Interfaces Manual IY(4)
NAME
iy -- Intel EtherExpress PRO/10 Ethernet driver (Intel i82595)
SYNOPSIS
iy0 at isa? port {port} irq ?
DESCRIPTION
The iy device driver supports the EtherExpress PRO/10 card, and might support other ISA cards using the same chip.
MEDIA SELECTION
The different models of the supported boards come with some subset of RJ-45, BNC and AUI connectors. Supported media include:
AUI/DIX Standard 15 pin connector
10Base2 BNC, also known as thin-net
10BaseT UTP, also known as twisted pair
The default port to use is the port the card autodetects at ifconfig up time. To choose an alternative port, an explicit medium can be spec-
ified to ifconfig(8) or in your ifconfig.iy? file.
NOTES
The EtherExpress PRO card has no jumpers to set the address. Intel supplies software to set the address of the card in software. You have
to hardwire this address in your kernel configuration file.
SEE ALSO
ed(4), eg(4), el(4), ep(4), intro(4), ix(4), le(4), ifconfig(8)
STANDARDS
are great. There's so many to choose from.
BSD
May 22, 1996 BSD