01-22-2015
If you know an address that would route through that card, just try a simple ping. It should re-plumb into when the switch is available again. It might be worth checking that the card and switch port agree on speed and other settings.
You might also get some useful information from entstat naming the device in question, e.g. entstat -d en1
I hope that this helps,
Robin
9 More Discussions You Might Find Interesting
1. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
2. AIX
Hello Gurus,
I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access??
1. netstat -Aan | grep <port... (1 Reply)
Discussion started by: tenderfoot
1 Replies
3. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
8. UNIX for Advanced & Expert Users
Hello all,
I need your help with any command to release a port on AIX.
Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies
9. AIX
Hello,
I have some doubt about the NIC device on my AIX box.
When using lsdev command
/ > lsdev -Cc adapter | grep en
ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2... (11 Replies)
Discussion started by: Phat
11 Replies
LEARN ABOUT NETBSD
eshconfig
ESHCONFIG(8) BSD System Manager's Manual ESHCONFIG(8)
NAME
eshconfig -- configure Essential Communications' HIPPI network interface
SYNOPSIS
eshconfig [-estx] [-b bytes] [-c bytes] [-d filename] [-i usecs] [-m bytes] [-r bytes] [-u filename] [-w bytes] [interface]
DESCRIPTION
eshconfig is used to configure device-specific parameters and download new firmware to the Essential Communications RoadRunner-based HIPPI
network interface. The interface is very sensitive to the DMA performance characteristics of the host, and so requires careful tuning to
achieve reasonable performance. In addition, firmware is likely to change frequently, which necessitates a reasonably easy way to update
that firmware.
Available operands for eshconfig:
-b bytes
Adjust the burst size for read (by NIC of host memory) DMA.
-c bytes
Adjust the burst size for write (by NIC of host memory) DMA.
-d filename
Filename for file to download into NIC firmware. This must be a file in the standard Essential format, with :04 preceding every
line, and a tag line at the end indicating the characteristics of the firmware file.
-e Write data to EEPROM. Normally, setting tuning parameters will only persist until the system is rebooted. Setting this parameter
ensures that the changes will be written to EEPROM.
-i usecs
Interrupt delay in microseconds.
-m bytes
Minimum number of bytes to DMA in one direction (read or write) before allowing a DMA in the other direction. Tuning this prevents
one direction from dominating the flow of bytes, and artificially throttling the NIC.
-r bytes
Bytes before DMA starts for read (from host to NIC). This controls how soon the DMA is triggered; until this many bytes are
requested, the DMA will not begin.
-s Show statistics for the HIPPI NIC. Repeat the option to suppress non-zero statistics.
-t Show current tuning parameters on the host.
-u filename
Name of file to which the NIC firmware should be uploaded. Not currently supported.
-w bytes
Number of bytes required before write (from NIC to host) DMA is started. Until this many bytes are ready to be written, the DMA will
not start.
-x Reset the NIC. This is necessary for the HIPPI-FP support, as ifconfig(8) will no longer physically reset the NIC when the inter-
faces goes up and down.
Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exist or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
esh(4), ifconfig(8)
HISTORY
The eshconfig command first appeared in NetBSD 1.4.
BSD
June 17, 2005 BSD