01-21-2015
AIX Frame: NIC port down
NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.
How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a Pri and Sec, so both VIO and LPAR ping.
OS AIX 6.1
9 More Discussions You Might Find Interesting
1. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
2. AIX
Hello Gurus,
I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access??
1. netstat -Aan | grep <port... (1 Reply)
Discussion started by: tenderfoot
1 Replies
3. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
8. UNIX for Advanced & Expert Users
Hello all,
I need your help with any command to release a port on AIX.
Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies
9. AIX
Hello,
I have some doubt about the NIC device on my AIX box.
When using lsdev command
/ > lsdev -Cc adapter | grep en
ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003)
ent2... (11 Replies)
Discussion started by: Phat
11 Replies
LEARN ABOUT DEBIAN
fence_vixel
fence_vixel(8) System Manager's Manual fence_vixel(8)
NAME
fence_vixel - I/O Fencing agent for Vixel FC switches
SYNOPSIS
fence_vixel [OPTION]...
DESCRIPTION
fence_vixel is an I/O Fencing agent which can be used with Vixel FC switches. It logs into a Vixel switch via telnet and removes the spec-
ified port from the zone. Removing the zone access from the port disables the port from being able to access the storage.
fence_vixel accepts options on the command line as well as from stdin. fenced sends parameters through stdin when it execs the agent.
fence_vixel can be run by itself with command line options which is useful for testing.
After a fence operation has taken place the fenced machine can no longer connect to the Vixel FC switch. When the fenced machine is ready
to be brought back into the GFS cluster (after reboot) the port on the Vixel FC switch needs to be enabled. In order to do this, log into
the Vixel FC switch. Then go to:
config->zones->config <port> <comma-separated-list-of-ports-in-the-zone>
Then apply
Consult the Vixel manual for details
Vendor URL: http://www.emulex.com
OPTIONS
-a IPaddress
IP address of the switch.
-h Print out a help message describing available options, then exit.
-n port
The port number to remove zoning from on the switch.
-p password
Password for login.
-S path
Full path to an executable to generate the password for login.
-V Print out a version message, then exit.
STDIN PARAMETERS
agent = < param >
This option is used by fence_node(8) and is ignored by fence_vixel.
ipaddr = < hostname | ip >
IP address or hostname of the switch.
passwd = < param >
Password for login.
passwd_script = < param >
Full path to an executable to generate the password for login.
port = < param >
The port number to remove zoning from on the switch.
SEE ALSO
fence(8), fence_node(8)
fence_vixel(8)