Sponsored Content
Full Discussion: AIX Frame: NIC port down
Operating Systems AIX AIX Frame: NIC port down Post 302932483 by gps1976 on Wednesday 21st of January 2015 06:19:17 PM
Old 01-21-2015
AIX Frame: NIC port down

NIC port is down on IBM Frame. From the back its slot C7/C8. The network switch is the problem, and a new switch will be coming into play. There's one VIO and one LPAR.

How do i tell the port is down in the OS on the VIO? And how can i verify it's backup without pulling cables? We have a Pri and Sec, so both VIO and LPAR ping.
OS AIX 6.1
 

9 More Discussions You Might Find Interesting

1. AIX

Dual port NIC, cfgmgr

OS: AIX 6.1 The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install: `cfgmgr -v` on 10.15.xx.xxx cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies

2. AIX

Who's using my port in AIX

Hello Gurus, I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access?? 1. netstat -Aan | grep <port... (1 Reply)
Discussion started by: tenderfoot
1 Replies

3. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

8. UNIX for Advanced & Expert Users

How to release port on AIX?

Hello all, I need your help with any command to release a port on AIX. Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies

9. AIX

AIX - NIC device explanation need

Hello, I have some doubt about the NIC device on my AIX box. When using lsdev command / > lsdev -Cc adapter | grep en ent0 Available 03-00 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent1 Available 03-01 2-Port 10/100/1000 Base-TX PCI-Express Adapter (14104003) ent2... (11 Replies)
Discussion started by: Phat
11 Replies
wxLayoutAlgorithm(3erl) 				     Erlang Module Definition					   wxLayoutAlgorithm(3erl)

NAME
wxLayoutAlgorithm - See external documentation: wxLayoutAlgorithm. DESCRIPTION
See external documentation: wxLayoutAlgorithm . DATA TYPES
wxLayoutAlgorithm() : An object reference, The representation is internal and can be changed without notice. It can't be used for comparsion stored on disc or distributed for use on other nodes. EXPORTS
new() -> wxLayoutAlgorithm() See external documentation . layoutFrame(This::wxLayoutAlgorithm(), Frame::wxFrame() (see module wxFrame)) -> bool() Equivalent to layoutFrame(This, Frame, []) . layoutFrame(This::wxLayoutAlgorithm(), Frame::wxFrame() (see module wxFrame), Options::[Option]) -> bool() Types Option = {mainWindow, wxWindow() (see module wxWindow)} See external documentation . layoutMDIFrame(This::wxLayoutAlgorithm(), Frame::wxMDIParentFrame() (see module wxMDIParentFrame)) -> bool() Equivalent to layoutMDIFrame(This, Frame, []) . layoutMDIFrame(This::wxLayoutAlgorithm(), Frame::wxMDIParentFrame() (see module wxMDIParentFrame), Options::[Option]) -> bool() Types Option = {rect, {X::integer(), Y::integer(), W::integer(), H::integer()}} See external documentation . layoutWindow(This::wxLayoutAlgorithm(), Frame::wxWindow() (see module wxWindow)) -> bool() Equivalent to layoutWindow(This, Frame, []) . layoutWindow(This::wxLayoutAlgorithm(), Frame::wxWindow() (see module wxWindow), Options::[Option]) -> bool() Types Option = {mainWindow, wxWindow() (see module wxWindow)} See external documentation . destroy(This::wxLayoutAlgorithm()) -> ok Destroys this object, do not use object again AUTHORS
<> wxErlang 0.98.9 wxLayoutAlgorithm(3erl)
All times are GMT -4. The time now is 05:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy