Sponsored Content
Operating Systems Linux Interface goes down after 2 minutes Post 302932414 by Corona688 on Wednesday 21st of January 2015 11:43:35 AM
Old 01-21-2015
Something is, though. That's what "promiscuous mode" means, it will receive packets to any destination. Things like wireshark and tcpdump use it to monitor the connection.

What programs / services are you running? You need to find what is putting it into that mode. Whatever it is, is what I suspect is messing up your connection.
 

9 More Discussions You Might Find Interesting

1. Shell Programming and Scripting

Convert minutes to hours, minutes, seconds

How would you convert lets say a 1000 minutes to hours, minutes, seconds (1 Reply)
Discussion started by: Vozx
1 Replies

2. Shell Programming and Scripting

ls every 5 minutes

I have to check for a directory content: every time it is filled with a file, I have to launch a bash script. So: how to do an ls every 5 minutes (avoiding cron), telling the script to start if the file has appeared in the dir? Have you got better ideas? Thanks in advance! (5 Replies)
Discussion started by: canduc17
5 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

6. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

7. UNIX for Beginners Questions & Answers

How to convert days hours minutes seconds to minutes?

Hi, please help with below time conversion to minutes. one column values: 2 minutes 16 seconds 420 msec 43 seconds 750 msec 0 days 3 hours 29 minutes 58 seconds 480 msec 11 seconds 150 msec I need output in minutes(total elapsed time in minutes) (2 Replies)
Discussion started by: ramu.badugula
2 Replies

8. Shell Programming and Scripting

Grep a log file for the last 5 minutes of contents every 5 minutes

Hi all, System Ubuntu 16.04.3 LTS i have the following log INFO 2019-02-07 15:13:31,099 module.py:700] default: "POST /join/8550614e-3e94-4fa5-9ab2-135eefa69c1b HTTP/1.0" 500 2042 INFO 2019-02-07 15:13:31,569 module.py:700] default: "POST /join/6cb9c452-dcb1-45f3-bcca-e33f5d450105... (15 Replies)
Discussion started by: charli1
15 Replies

9. Shell Programming and Scripting

Check file creation Time minutes and if file older then 5 minutes execute some stuff

Hello all, Info: System RedHat 7.5 I need to create a script that based on the creation time, if the file is older then 5 minutes then execute some stuff, if not exit. I thought to get the creation time and minutes like this. CreationTime=$(stat -c %y /tmp/test.log | awk -F" " '{ print... (3 Replies)
Discussion started by: charli1
3 Replies
PCAP_ACTIVATE(3PCAP)													      PCAP_ACTIVATE(3PCAP)

NAME
pcap_activate - activate a capture handle SYNOPSIS
#include <pcap/pcap.h> int pcap_activate(pcap_t *p); DESCRIPTION
pcap_activate() is used to activate a packet capture handle to look at packets on the network, with the options that were set on the handle being in effect. RETURN VALUE
pcap_activate() returns 0 on success without warnings, PCAP_WARNING_PROMISC_NOTSUP on success on a device that doesn't support promiscuous mode if promiscuous mode was requested, PCAP_WARNING_TSTAMP_TYPE_NOTSUP on success if the time stamp type specified in a previous pcap_set_tstamp_type() call isn't supported by the capture source (the time stamp type is left as the default), PCAP_WARNING on success with any other warning, PCAP_ERROR_ACTIVATED if the handle has already been activated, PCAP_ERROR_NO_SUCH_DEVICE if the capture source specified when the handle was created doesn't exist, PCAP_ERROR_PERM_DENIED if the process doesn't have permission to open the capture source, PCAP_ERROR_PROMISC_PERM_DENIED if the process has permission to open the capture source but doesn't have permission to put it into promiscuous mode, PCAP_ERROR_RFMON_NOTSUP if monitor mode was specified but the capture source doesn't support monitor mode, PCAP_ERROR_IFACE_NOT_UP if the capture source is not up, and PCAP_ERROR if another error occurred. If PCAP_WARNING or PCAP_ERROR is returned, pcap_geterr() or pcap_perror() may be called with p as an argument to fetch or display a message describing the warning or error. If PCAP_WARNING_PROMISC_NOTSUP, PCAP_ERROR_NO_SUCH_DEVICE, or PCAP_ERROR_PERM_DENIED is returned, pcap_geterr() or pcap_perror() may be called with p as an argument to fetch or display an message giving additional details about the problem that might be useful for debugging the problem if it's unexpected. SEE ALSO
pcap(3PCAP) 5 April 2008 PCAP_ACTIVATE(3PCAP)
All times are GMT -4. The time now is 06:29 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy