01-21-2015
Something is, though. That's what "promiscuous mode" means, it will receive packets to any destination. Things like wireshark and tcpdump use it to monitor the connection.
What programs / services are you running? You need to find what is putting it into that mode. Whatever it is, is what I suspect is messing up your connection.
9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
How would you convert lets say a 1000 minutes to hours, minutes, seconds (1 Reply)
Discussion started by: Vozx
1 Replies
2. Shell Programming and Scripting
I have to check for a directory content: every time it is filled with a file, I have to launch a bash script.
So: how to do an ls every 5 minutes (avoiding cron), telling the script to start if the file has appeared in the dir?
Have you got better ideas?
Thanks in advance! (5 Replies)
Discussion started by: canduc17
5 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
5. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
6. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
7. UNIX for Beginners Questions & Answers
Hi, please help with below time conversion to minutes.
one column values:
2 minutes 16 seconds 420 msec
43 seconds 750 msec
0 days 3 hours 29 minutes 58 seconds 480 msec
11 seconds 150 msec
I need output in minutes(total elapsed time in minutes) (2 Replies)
Discussion started by: ramu.badugula
2 Replies
8. Shell Programming and Scripting
Hi all,
System Ubuntu 16.04.3 LTS
i have the following log
INFO 2019-02-07 15:13:31,099 module.py:700] default: "POST /join/8550614e-3e94-4fa5-9ab2-135eefa69c1b HTTP/1.0" 500 2042
INFO 2019-02-07 15:13:31,569 module.py:700] default: "POST /join/6cb9c452-dcb1-45f3-bcca-e33f5d450105... (15 Replies)
Discussion started by: charli1
15 Replies
9. Shell Programming and Scripting
Hello all,
Info:
System RedHat 7.5
I need to create a script that based on the creation time,
if the file is older then 5 minutes then execute some stuff, if not exit.
I thought to get the creation time and minutes like this.
CreationTime=$(stat -c %y /tmp/test.log | awk -F" " '{ print... (3 Replies)
Discussion started by: charli1
3 Replies
LEARN ABOUT SUSE
ifsysctl
IFSYSCTL(5) Network configuration IFSYSCTL(5)
NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO
ifup(8) ifcfg(5) sysctl(8)
sysconfig December 2009 IFSYSCTL(5)