01-21-2015
You already have a topic for your problem.
Topic continues
here.
9 More Discussions You Might Find Interesting
1. IP Networking
/* SCO OpenServer 5 */
anyone know an effective way to tell what machines, if any, are running in promiscuous mode??
e0- (1 Reply)
Discussion started by: LowOrderBit
1 Replies
2. IP Networking
Hallo,
I want to use tcpdump to analyze the NTP traffic on some of my machines. The machines that I want to analyze run HP-UX and linux. To use tcpdump 2 packages are required Libpcap and Tcpdump. I know that tcpdump (libcap?) sets the network interface to promiscuous mode. I have some... (1 Reply)
Discussion started by: one71
1 Replies
3. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
4. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
5. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
6. UNIX for Advanced & Expert Users
Hi All,
Can please let me know what is the difference between the single line mode and multi line mode in regular expresions?
Thanks,
Chidhambaram B (3 Replies)
Discussion started by: chidhu.anu
3 Replies
7. AIX
Hi Guys,
What do I need to do to set an physical adapter to promiscuous mode?
The networkport is already spanned/mirrored.
Is this also possible when there is an virtual nic (through vios) configured?
regards,
Randy (7 Replies)
Discussion started by: raba
7 Replies
8. UNIX for Dummies Questions & Answers
Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OSX
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to a network node
SYNOPSIS
traceroute6 [-dIlnNrvU] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
The traceroute6 utility uses the IPv6 protocol hop limit field to elicit an ICMPv6 TIME_EXCEEDED response from each gateway along the path to
some host.
The only mandatory parameter is the destination host name or IPv6 address. The default probe datagram carries 12 bytes of payload, in addi-
tion to the IPv6 header. The size of the payload can be specified by giving a length (in bytes) after the destination host name.
Other options are:
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit, up to 255. The default is 30 hops.
-n Do not resolve numeric address to hostname.
-N Use a packet with no upper layer header for the probes, instead of UDP datagrams.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-connected net-
work, an error is returned. This option corresponds to the SO_DONTROUTE socket option; it can be used to ping a local host through
an interface that has no route through it (e.g., after the interface was dropped by a routing daemon).
-s src Src specifies the source IPv6 address to be used.
-U Use UDP datagrams for the probes. This is the default.
-v Be verbose.
-w waittime
Specify the delay time between probes.
This program prints the route to the given destination and the round-trip time to each gateway, in the same manner as traceroute.
Here is a list of possible annotations after the round-trip time for each gateway:
!N Destination Unreachable - No Route to Host.
!P Destination Unreachable - Administratively Prohibited.
!S Destination Unreachable - Not a Neighbour.
!A Destination Unreachable - Address Unreachable.
! This is printed if the hop limit is <= 1 on a port unreachable message. This means that the packet got to the destination, but
that the reply had a hop limit that was just large enough to allow it to get back to the source of the traceroute6. This was
more interesting in the IPv4 case, where some IP stack bugs could be identified by this behaviour.
RETURN VALUES
The traceroute6 utility will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD