Sponsored Content
Operating Systems Linux Red Hat Interface goes into promiscuous mode Post 302932413 by Corona688 on Wednesday 21st of January 2015 11:42:02 AM
Old 01-21-2015
You already have a topic for your problem.

Topic continues here.
 

9 More Discussions You Might Find Interesting

1. IP Networking

promiscuous mode machines

/* SCO OpenServer 5 */ anyone know an effective way to tell what machines, if any, are running in promiscuous mode?? e0- (1 Reply)
Discussion started by: LowOrderBit
1 Replies

2. IP Networking

tcpdump and promiscuous mode (on Linux and HP-UX)

Hallo, I want to use tcpdump to analyze the NTP traffic on some of my machines. The machines that I want to analyze run HP-UX and linux. To use tcpdump 2 packages are required Libpcap and Tcpdump. I know that tcpdump (libcap?) sets the network interface to promiscuous mode. I have some... (1 Reply)
Discussion started by: one71
1 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

6. UNIX for Advanced & Expert Users

What is the difference between single line mode and multiline mode in Regular expressions?

Hi All, Can please let me know what is the difference between the single line mode and multi line mode in regular expresions? Thanks, Chidhambaram B (3 Replies)
Discussion started by: chidhu.anu
3 Replies

7. AIX

promiscuous mode AIX

Hi Guys, What do I need to do to set an physical adapter to promiscuous mode? The networkport is already spanned/mirrored. Is this also possible when there is an virtual nic (through vios) configured? regards, Randy (7 Replies)
Discussion started by: raba
7 Replies

8. UNIX for Dummies Questions & Answers

Will Linux force NIC into promiscuous mode?

Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
DNPING(1)						      General Commands Manual							 DNPING(1)

NAME
dnping - Loopbacks diagnostic packets through a remote node SYNOPSIS
dnping nodename [user pass] count or dnping nodename [options] nodename Options: [qsv] [-c number] [-i interval] [-p password] [-s size] [-u username] [-w timeout] DESCRIPTION
This utility sends to remote DECnet node nodename the number of packets specified by count to test the link between the two systems. Optionally a username and password may be specified for the connection as well as several other options. NOTE that if you dnping another Linux box it must have dnetd running. NOTE also that dnping is not really like an IP "ping" in that it needs a registered object at the other end to connect to. So, just because you cannot ping a machine does not, necessarily, mean that machine is not available, just that the MIRROR object is not available. There is not (to my knowledge) a low-level equivalent in DECnet of the ICMP ping message. OPTIONS
-c number Number of packets to send (default 10) -d Debug mode (default off) -i interval interval between packets in microseconds (default 0) -p password Access control password. If this is "-" then you will be prompted. -q Quiet mode (default off) -s size size of frame to send in bytes (40 data + 68 hdr) -t timestamps mode (default off) -u username access control username -w timeout Specifies a timeout (in seconds). If not response is received after this time then dnping will abort. The default is to wait for- ever. -v verbose mode (default off) EXAMPLES
Pings 10 packets through remote node "mv3100" # dnping mv3100 10 Make it look a bit like IP ping: # dnping -vti 1000000 marsha SEE ALSO
dntype(1), dndir(1), dndel(1), dntask(1), sethost(1), dnetd(8) DECnet utilities January 25 2000 DNPING(1)
All times are GMT -4. The time now is 11:12 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy