Sponsored Content
Operating Systems Solaris Hardware RAID using three disks Post 302931999 by jegaraman on Sunday 18th of January 2015 02:36:57 AM
Old 01-18-2015
Dear Hicks/Germany ,

Pl see the below output ,

Code:
 metadb
        flags           first blk       block count
     a m  pc luo        16              8192            /dev/dsk/c1t3d0s7
     a    pc luo        8208            8192            /dev/dsk/c1t3d0s7
root@  #
root@ # metastat
d10: Concat/Stripe
    Size: 1170211752 blocks (558 GB)
    Stripe 0:
        Device     Start Block  Dbase   Reloc
        c1t3d0s0          0     No      Yes

Device Relocation Information:
Device   Reloc  Device ID
c1t3d0   Yes    id1,sd@n5000cca025002fa8
root@ #
root@  # swap -l
swapfile             dev  swaplo blocks   free
/dev/dsk/c1t0d0s1   32,1      16 32768720 32768720
root@  #
root@ # zpool status
no pools available
root@  #

From the above output , the third disk c1t3d0 is used for SVM.

and also the swap is used by c1t0d0.....

So Kindly describe how to do the patching in case if we have hardware raid and also SVM in same server.Or any other ways to handle this.As there is no backup available for the above servers, I am going to split the hardware raid and do the patching. So how to take care of this third disk under SVM.

Rgds ,
Rj
 

9 More Discussions You Might Find Interesting

1. Solaris

Hardware RAID

I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies

2. Red Hat

IBM RAID disks

We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies

3. Solaris

Move disks to different StorEdge, keeping RAID

Hi. I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID. Essentially, the quesion is, how can this be done? :confused: I checked... (5 Replies)
Discussion started by: alexs77
5 Replies

4. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

5. Solaris

Solaris not recognizing RAID 5 disks

I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies

6. AIX

SCSI PCI - X RAID Controller card RAID 5 AIX Disks disappeared

Hello, I have a scsi pci x raid controller card on which I had created a disk array of 3 disks when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk ) suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies

7. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies

8. Solaris

Solaris 10 Installation - Disks missing, and Raid

Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes. Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies

9. Solaris

Hardware raid patching

Dear All , we have hardware raid 1 implemented on Solaris Disks. We need to patch the Servers. Kindly let me know how to patch hardware raid implemented Servers. Thanks... Rj (7 Replies)
Discussion started by: jegaraman
7 Replies
disks(1M)						  System Administration Commands						 disks(1M)

NAME
disks - creates /dev entries for hard disks attached to the system SYNOPSIS
/usr/sbin/disks [-C] [-r rootdir] DESCRIPTION
devfsadm(1M) is now the preferred command for /dev and should be used instead of disks. disks creates symbolic links in the /dev/dsk and /dev/rdsk directories pointing to the actual disk device special files under the /devices directory tree. It performs the following steps: 1. disks searches the kernel device tree to see what hard disks are attached to the system. It notes the /devices pathnames for the slices on the drive and determines the physical component of the corresponding /dev/dsk or /dev/rdsk name. 2. The /dev/dsk and /dev/rdsk directories are checked for disk entries - that is, symbolic links with names of the form cN[tN]dNsN, or cN[tN]dNpN, where N represents a decimal number. cN is the logical controller number, an arbitrary number assigned by this program to designate a particular disk controller. The first controller found on the first occasion this program is run on a system, is assigned number 0. tN is the bus-address number of a subsidiary controller attached to a peripheral bus such as SCSI or IPI (the target number for SCSI, and the facility number for IPI controllers). dN is the number of the disk attached to the controller. sN is the slice number on the disk. pN is the FDISK partition number used by fdisk(1M). (x86 Only) 3. If only some of the disk entries are found in /dev/dsk for a disk that has been found under the /devices directory tree, disks creates the missing symbolic links. If none of the entries for a particular disk are found in /dev/dsk, disks checks to see if any entries exist for other disks attached to the same controller, and if so, creates new entries using the same controller number as used for other disks on the same controller. If no other /dev/dsk entries are found for slices of disks belonging to the same physical con- troller as the current disk, disks assigns the lowest-unused controller number and creates entries for the disk slices using this newly-assigned controller number. disks is run automatically each time a reconfiguration-boot is performed or when add_drv(1M) is executed. When invoking disks(1M) manually, first run drvconfig(1M) to ensure /devices is consistent with the current device configuration. Notice to Driver Writers disks considers all devices with a node type of DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, DDI_NT_BLOCK_WWN or DDI_NT_CD_CHAN to be disk devices. disks(1M) requires the minor name of disk devices obey the following format conventions. The minor name for block interfaces consists of a single lowercase ASCII character, a through u. The minor name for character (raw) inter- faces consists of a single lowercase ASCII character, a through u, followed by ,raw. disks translates a through p to s0 through s15, while it translates q through u to p0 through p4. SPARC drivers should only use the first 8 slices: a through h, while x86 drivers can use a through u, with q through u corresponding to fdisk(1M) partitions. q represents the entire disk, while r, s, t, and u represent up to 4 additional partitions. To prevent disks from attempting to automatically generate links for a device, drivers must specify a private node type and refrain from using a node type: DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, or DDI_NT_CD_CHAN when calling ddi_create_minor_node(9F). OPTIONS
The following options are supported: -C Causes disks to remove any invalid links after adding any new entries to /dev/dsk and /dev/rdsk. Invalid links are links which refer to non-existent disk nodes that have been removed, powered off, or are otherwise inaccessible. -r rootdir Causes disks to presume that the /dev/dsk, /dev/rdsk and /devices directory trees are found under rootdir, not directly under /. ERRORS
If disks finds entries of a particular logical controller linked to different physical controllers, it prints an error message and exits without making any changes to the /dev directory, since it cannot determine which of the two alternative logical-to-physical mappings is correct. The links should be manually corrected or removed before another reconfiguration-boot is performed. EXAMPLES
Example 1: Creating Block and Character Minor Devices The following example demonstrates creating the block and character minor devices from within the xkdisk driver's attach(9E) function. #include <sys/dkio.h> /* * Create the minor number by combining the instance number * with the slice number. */ #define MINOR_NUM(i, s) ((i) << 4 | (s)) int xkdiskattach(dev_info_t *dip, ddi_attach_cmd_t cmd) { int instance, slice; char name[8]; /* other stuff in attach... */ instance = ddi_get_instance(dip); for (slice = 0; slice < V_NUMPAR; slice++) { /* * create block device interface */ sprintf(name, "%c", slice + 'a'); ddi_create_minor_node(dip, name, S_IFBLK, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); /* * create the raw (character) device interface */ sprintf(name,"%c,raw", slice + 'a'); ddi_create_minor_node(dip, name, S_IFCHR, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); } } Installing the xkdisk disk driver on a Sun Fire 4800, with the driver controlling a SCSI disk (target 3 attached to an isp(7D) SCSI HBA) and performing a reconfiguration-boot (causing disks to be run) creates the following special files in /devices. # ls -l /devices/ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/ brw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a crw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a,raw brw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b crw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b,raw brw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c crw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c,raw brw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d crw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d,raw brw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e crw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e,raw brw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f crw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f,raw brw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g crw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g,raw brw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h crw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h,raw /dev/dsk will contain the disk entries to the block device nodes in /devices # ls -l /dev/dsk /dev/dsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a /dev/dsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b /dev/dsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c /dev/dsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d /dev/dsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e /dev/dsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f /dev/dsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g /dev/dsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h and /dev/rdsk will contain the disk entries for the character device nodes in /devices # ls -l /dev/rdsk /dev/rdsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a,raw /dev/rdsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b,raw /dev/rdsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c,raw /dev/rdsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d,raw /dev/rdsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e,raw /dev/rdsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f,raw /dev/rdsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g,raw /dev/rdsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h,raw FILES
/dev/dsk/* Disk entries (block device interface) /dev/rdsk/* Disk entries (character device interface) /devices/* Device special files (minor device nodes) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
add_drv(1M), devfsadm(1M), fdisk(1M), attributes(5), isp(7D), devfs(7FS), dkio(7I), attach(9E), ddi_create_minor_node(9F) Writing Device Drivers BUGS
disks silently ignores malformed minor device names. SunOS 5.10 7 Nov 2002 disks(1M)
All times are GMT -4. The time now is 08:36 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy