01-14-2015
@MadeInGermany........good point. Thanks. From a previous, but related, thread we know the system is ufs not zfs.
This User Gave Thanks to hicksd8 For This Post:
9 More Discussions You Might Find Interesting
1. Solaris
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Discussion started by: jess_t03
7 Replies
2. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
3. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
we have hardware raid 1 implemented on Solaris Disks.
We need to patch the Servers. Kindly let me know how to patch hardware raid implemented Servers.
Thanks...
Rj (7 Replies)
Discussion started by: jegaraman
7 Replies
LEARN ABOUT SUNOS
volcopy_ufs
volcopy_ufs(1M) System Administration Commands volcopy_ufs(1M)
NAME
volcopy_ufs - make an image copy of a ufs file system
SYNOPSIS
volcopy [ -F ufs] [generic_options] fsname srcdevice volname1 destdevice volname2
DESCRIPTION
volcopy makes a literal copy of the ufs file system using a blocksize matched to the device.
OPTIONS
The following option is supported:
generic_options options supported by the generic volcopy command. See volcopy(1M).
OPERANDS
The following operands are supported:
fsname represents the mount point (for example, root, u1, etc.) of the file system being copied.
srcdevice or destdevice the disk partition specified using the raw device (for example, /dev/rdsk/cld0s8, /dev/rdsk/cld1s8, etc.).
srcdevice and volname1 the device and physical volume from which the copy of the file system is being extracted.
destdevice and volname2 the target device and physical volume.
fsname and volname are limited to six or fewer characters and recorded in the superblock. volname may be `-' to use the existing volume
name.
EXIT STATUS
The following exit values are returned:
0 Successful file system copy.
non-zero An error has occurred.
FILES
/var/adm/filesave.log a record of file systems/volumes copied
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
cpio(1), dd(1M), labelit(1M), volcopy(1M), attributes(5), ufs(7FS)
NOTES
volcopy does not support copying to tape devices. Use dd(1M) for copying to and from tape devices.
SunOS 5.10 15 Apr 2003 volcopy_ufs(1M)