01-02-2015
You mean the VPN is disconnecting even though connectivity seems fine?
9 More Discussions You Might Find Interesting
1. Cybersecurity
Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Discussion started by: eNTer
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
Does any one knows any tools or method to monitor users all activities on Solaris 8, including command and its result. Similar to 'script' ???
Thanks
nana (3 Replies)
Discussion started by: nana
3 Replies
3. UNIX for Advanced & Expert Users
Hello,
I am within a LAN system and I need to be able to tunnel out (and recv UDP) packets.
Currently the router automatically drops UDP packets.
My PC cant see the outside world, nor ping, but it can connect via SSH to a server on the "edge" of the network which can see everything. I... (2 Replies)
Discussion started by: ErNci
2 Replies
4. Solaris
Hi,
I have tried the following:
on PC1 (win xp) I have created ssh connection with port forwarding
(local 8888 to remote 8888) to server1.
>From server1 I have created another ssh connection with port
forwarding to server2(local 8888 to remote 1521).
When I try to connect to oracle... (3 Replies)
Discussion started by: goran00
3 Replies
5. UNIX for Advanced & Expert Users
Was wonder if there was a tool or program I could run to measure throughput on our CentoS 4.x server. Our current dedicated host provider is charging us by how much throughput we are using and I just want to see if their numbers add up to whatever I get using a throughput tool of some kind.
... (6 Replies)
Discussion started by: mcraul
6 Replies
6. AIX
Dear experts ,
Pls advice for any good Tool to monitor the CPU and performance of AIX the system ..
to keep monitoring to show me the utilization of that system .. (12 Replies)
Discussion started by: Mr.AIX
12 Replies
7. IP Networking
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Discussion started by: salukibob
0 Replies
8. IP Networking
Hi all,
I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
Discussion started by: ivancd
4 Replies
9. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
LEARN ABOUT DEBIAN
gnunet-vpn
GNUNET-VPN(1) General Commands Manual GNUNET-VPN(1)
NAME
gnunet-vpn - manually setup a GNUnet VPN tunnel
SYNOPSIS
gnunet-vpn [options]
DESCRIPTION
gnunet-vpn can be used to manually setup a VPN tunnel via the GNUnet network. There are two main types of tunnels. Tunnels to an exit
node which routes the traffic to the global Internet, and tunnels to a node that runs a service only within GNUnet. Depending on the type
of tunnel, gnunet-vpn takes different options. The "-i" option is required for tunnels to an exit node, whereas the "-p" and "-s" options
in conjunction with either "-u" or "-t" are required for tunnels to services. For exit tunnels, both UDP and TCP traffic will be redi-
rected. For service tunnels, either UDP ("-u") or TCP ("-t") traffic will be redirected.
The tool will display the IP address for this end of the tunnel. The address can be displayed as soon as it has been allocated, or only
after ("-a") the tunnel has been created.
OPTIONS
-4, --ipv4
Desired IP address on this end of the tunnel should be an IPv4 address.
-6, --ipv6
Desired IP address on this end of the tunnel should be an IPv6 address.
-a, --after-connect
Display IP address only after the tunnel is fully connected.
-c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
-d SEC, --duration SEC
The mapping should be established for SEC seconds. Default is 5 minutes.
-h, --help
Print short help on options.
-i IP, --ip IP
Tunnel should be to an exit node and connect to the given IPv4 or IPv6 IP address. Note that you can specify an IPv6 address as the
target here, even in combination with "-4" (4to6) and similarly you can specify an IPv4 address in combination with "-6" (6to4).
-L LOGLEVEL, --loglevel=LOGLEVEL
Use LOGLEVEL for logging. Valid values are DEBUG, INFO, WARNING and ERROR.
-p PEERID, --peer=PEERID
Name of the peer offering the service to connect to. Cannot be used in conjunction with "-i", requires "-s".
-s NAME, --service=NAME
Name of the service running on the target peer. Cannot be used in conjunction with "-i", requires "-p".
-t, --tcp
Service runs TCP. Either "-t" or "-u" must be specified when using "-s".
-u, --udp
Service runs UDP. Either "-t" or "-u" must be specified when using "-s".
-V, --verbose
Be verbose.
-v, --version
Print GNUnet version number.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO
gnunet-setup(1)
GNUnet 25 Feb 2012 GNUNET-VPN(1)