12-30-2014
Best tool to monitor VPN IPSEC Tunneling
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity.
9 More Discussions You Might Find Interesting
1. Cybersecurity
Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Discussion started by: eNTer
3 Replies
2. UNIX for Dummies Questions & Answers
Hello,
Does any one knows any tools or method to monitor users all activities on Solaris 8, including command and its result. Similar to 'script' ???
Thanks
nana (3 Replies)
Discussion started by: nana
3 Replies
3. UNIX for Advanced & Expert Users
Hello,
I am within a LAN system and I need to be able to tunnel out (and recv UDP) packets.
Currently the router automatically drops UDP packets.
My PC cant see the outside world, nor ping, but it can connect via SSH to a server on the "edge" of the network which can see everything. I... (2 Replies)
Discussion started by: ErNci
2 Replies
4. Solaris
Hi,
I have tried the following:
on PC1 (win xp) I have created ssh connection with port forwarding
(local 8888 to remote 8888) to server1.
>From server1 I have created another ssh connection with port
forwarding to server2(local 8888 to remote 1521).
When I try to connect to oracle... (3 Replies)
Discussion started by: goran00
3 Replies
5. UNIX for Advanced & Expert Users
Was wonder if there was a tool or program I could run to measure throughput on our CentoS 4.x server. Our current dedicated host provider is charging us by how much throughput we are using and I just want to see if their numbers add up to whatever I get using a throughput tool of some kind.
... (6 Replies)
Discussion started by: mcraul
6 Replies
6. AIX
Dear experts ,
Pls advice for any good Tool to monitor the CPU and performance of AIX the system ..
to keep monitoring to show me the utilization of that system .. (12 Replies)
Discussion started by: Mr.AIX
12 Replies
7. IP Networking
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Discussion started by: salukibob
0 Replies
8. IP Networking
Hi all,
I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
Discussion started by: ivancd
4 Replies
9. IP Networking
Hi @all,
I try to connect 2 LANs with IPSec/Openswan
LAN 1: 192.168.0.0/24
LAN 2: 192.168.1.0/24
This is my Config:
conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)
NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD
April 11, 1998 BSD