If the ports of your router are 100MB full duplex it should be the same HP-UX side, avoid auto unless you have GB...
you can checkout with lanadmin command
Did you use setparms to configure your IP etc...?
Ping is not enough to say all is working, have you another host in your network you can connect to from your HP-UX if so, connect to th remote and try to transfer a big file, if ttransparent then it seems to work if dead slow then you have a network conf mismatch, it must be solved before trying internet... the most plausible is port mismatch like your HP-UX is 10 halfduplex and your router is 100 full, or both are 100 but failed in auto and set to half (HP-UX side ).
Your
shows probably your resolv.conf is not set or is not properly set
It needs a DNS server...
Give it the address of your router and see if it works, since I have never trying to configure hosts privately, I dont know what you should put for a domain name
I would try home or nothing and put a line with:
I let you search for that
for the nsswitch.conf file, for the line host you can try something like
but try to look for samples because I am at home for another week at least in bed and have no access to my docs... and with my medication I doubt having memory at optimum...
Courage and good luck
Hi People!
I've just got a HP-UX system dumped on me. I've started it, followed all the install/setup questions, and everything was going ok, right upto when going into the desktop enviroment I got the message "The Desktop Messaging System Could Not Be Started".
Now I've checked the... (8 Replies)
Hello folks, had a question.
I was trying to install sudotool on HP -UX 11i.
I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box
how do i install it??
do i need to run "swinstall" menu and then choose from there?
THanks!
karthik (1 Reply)
Hi Experts
I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error.
ENTRY_INIT failed, status = -4: Unrecoverable hardware error
(followed by a hex dump)
I have re-tried many times and on one occasion successfully got through to CD... (4 Replies)
Hey,
i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write
BOot P1
P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said:
P0 scsiA.6 HP73.4MAT3073NP
P1 ide.1 ... (2 Replies)
Hello All,
I am getting " The DT messaging system could not be started" message when wants to login as root on a box running on tru64 5.1A.
/etc/hosts is ok.
when i see in .dt/errorlog it shows message server could not be started.
Thanks for help.
Awadhesh (2 Replies)
hi all,
I want to install iplanet messaging service in solaris 10.
if it is possible plz send the procedure for installation.its urgent plz
regards
spandan (2 Replies)
Hi there,
hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de).
I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image... (1 Reply)
I have an application rpm which when installed is failing to get installed with error
error: Failed dependencies:
libc.so.6 is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.0) is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.1) is needed by testSam-4.7.x86_64
... (1 Reply)
Good Morning,
Users can no longer log into SunBlade 2500 Solaris 9 system (though root still can). Here's what I'm getting and what I've done. I'm most suspicious of the full drive since that pops up twice and I did see one looks full. What's a good way to reduce what's on it?- or.. what else... (2 Replies)