Help needed HP UX 11.11i new install on C8000 Desktop messaging system error CAN'T FIX Post: 302929790

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

The Desktop Messaging System Could Not Be Started HP-UX

Hi People! I've just got a HP-UX system dumped on me. I've started it, followed all the install/setup questions, and everything was going ok, right upto when going into the desktop enviroment I got the message "The Desktop Messaging System Could Not Be Started". Now I've checked the...

2. UNIX for Dummies Questions & Answers

sudo install on HP UX 11i(basic question)

Hello folks, had a question. I was trying to install sudotool on HP -UX 11i. I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box how do i install it?? do i need to run "swinstall" menu and then choose from there? THanks! karthik

3. HP-UX

11i install error

Hi Experts I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error. ENTRY_INIT failed, status = -4: Unrecoverable hardware error (followed by a hex dump) I have re-tried many times and on one occasion successfully got through to CD...

4. HP-UX

HP UX 11i and HP C8000

Hey, i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write BOot P1 P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said: P0 scsiA.6 HP73.4MAT3073NP P1 ide.1 ...

5. UNIX for Advanced & Expert Users

The DT messaging system could not be started

Hello All, I am getting " The DT messaging system could not be started" message when wants to login as root on a box running on tru64 5.1A. /etc/hosts is ok. when i see in .dt/errorlog it shows message server could not be started. Thanks for help. Awadhesh

6. Solaris

how to install iplanet messaging server 5.2 on solaris 10

hi all, I want to install iplanet messaging service in solaris 10. if it is possible plz send the procedure for installation.its urgent plz regards spandan

7. HP-UX

RX2620 11i V3 install halts at load ram disk

Hi there, hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de). I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image...

8. Red Hat

RPM Install error: libc.so.6 is needed by

I have an application rpm which when installed is failing to get installed with error error: Failed dependencies: libc.so.6 is needed by testSam-4.7.x86_64 libc.so.6(GLIBC_2.0) is needed by testSam-4.7.x86_64 libc.so.6(GLIBC_2.1) is needed by testSam-4.7.x86_64 ...

9. Shell Programming and Scripting

The DT messaging system could not be started.

Good Morning, Users can no longer log into SunBlade 2500 Solaris 9 system (though root still can). Here's what I'm getting and what I've done. I'm most suspicious of the full drive since that pops up twice and I did see one looks full. What's a good way to reduce what's on it?- or.. what else...

LEARN ABOUT MINIX

resolvxc

RESOLV.CONF(5)							File Formats Manual						    RESOLV.CONF(5)

NAME

       resolv.conf - Domain Name System resolver configuration

SYNOPSIS

       /etc/resolv.conf

DESCRIPTION

       The  /etc/resolv.conf  is used to configure how the host will use the Domain Name System to resolve hostnames to IP addresses.  It may con-
       tain these two lines:

	      nameserver     IP-address
	      domain	     domain-name

       The nameserver entry tells the IP address of the host to use for DNS queries.  If it is set to 127.0.0.1 (which is the  default)  then  the
       local  name  daemon is used that may use the /etc/hosts database to translate host names.  You normally only need a nameserver entry if the
       name server is at the other side of a router.  The default nonamed name server can't look beyond the local network.

       The domain entry tells the default domain to use for unqualified hostnames.  This entry is usually not given in which case  the	domain	of
       the local host is used.

       The long version of this story can be found in resolver(5).

FILES

       /etc/resolv.conf    DNS resolver configuration file.

SEE ALSO

       resolver(5), hosts(5), nonamed(8), boot(8).

AUTHOR

       Kees J. Bot (kjb@cs.vu.nl)

																    RESOLV.CONF(5)