12-26-2014
Thanks for your reply
ok have just finished installing os on my other C8000, minimal hardware, DID NOT select DCHP option for network, manually entered ip address for machine as 192.168.1.18, gateway as 192.168.1.1 which is the value I use for the ethernet to wifi adapter that I have set up previously to connect to wifi on ethernet hardware I own ( this is the value I use on my SGI Octane when using this adaptor) it boots into the CDE Desktop and I can operate everything fine (prev. if I select DCHP , network settings get assigned and I get an error about desktop messaging system and I cannot log in in anything but failsafe mode) however if I start up mozilla , it cannot find any pages, keeps saying good web address cannot be found , please check and try again. on the other computer , after fiddling with network settings, I could get mozilla to load pages BUT it would then come up with desktop messaging system error and I would have to log back in in failsafe mode and could run mozilla ok but obviously could not get to a standard CDE session. In summary CAN EITHER HAVE A STANDARD CDE LOGIN WITH NO ERROR ABOUT MESSAGING SYSTEM BUT NO INTERNET RUNNING MOZILLA.............OR .............. ONLY A FAILSAFE LOGIN BECAUSE OF DESKTOP MESSAGING ERROR HOWEVER MOZILLA DOES INFACT WORK. BUT........... NOT BOTH WORKING AT SAME TIME.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi People!
I've just got a HP-UX system dumped on me. I've started it, followed all the install/setup questions, and everything was going ok, right upto when going into the desktop enviroment I got the message "The Desktop Messaging System Could Not Be Started".
Now I've checked the... (8 Replies)
Discussion started by: cpiuk
8 Replies
2. UNIX for Dummies Questions & Answers
Hello folks, had a question.
I was trying to install sudotool on HP -UX 11i.
I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box
how do i install it??
do i need to run "swinstall" menu and then choose from there?
THanks!
karthik (1 Reply)
Discussion started by: karthikosu
1 Replies
3. HP-UX
Hi Experts
I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error.
ENTRY_INIT failed, status = -4: Unrecoverable hardware error
(followed by a hex dump)
I have re-tried many times and on one occasion successfully got through to CD... (4 Replies)
Discussion started by: C3000
4 Replies
4. HP-UX
Hey,
i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write
BOot P1
P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said:
P0 scsiA.6 HP73.4MAT3073NP
P1 ide.1 ... (2 Replies)
Discussion started by: numx
2 Replies
5. UNIX for Advanced & Expert Users
Hello All,
I am getting " The DT messaging system could not be started" message when wants to login as root on a box running on tru64 5.1A.
/etc/hosts is ok.
when i see in .dt/errorlog it shows message server could not be started.
Thanks for help.
Awadhesh (2 Replies)
Discussion started by: Awadhesh
2 Replies
6. Solaris
hi all,
I want to install iplanet messaging service in solaris 10.
if it is possible plz send the procedure for installation.its urgent plz
regards
spandan (2 Replies)
Discussion started by: spandhan
2 Replies
7. HP-UX
Hi there,
hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de).
I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image... (1 Reply)
Discussion started by: plantage
1 Replies
8. Red Hat
I have an application rpm which when installed is failing to get installed with error
error: Failed dependencies:
libc.so.6 is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.0) is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.1) is needed by testSam-4.7.x86_64
... (1 Reply)
Discussion started by: rupeshkp728
1 Replies
9. Shell Programming and Scripting
Good Morning,
Users can no longer log into SunBlade 2500 Solaris 9 system (though root still can). Here's what I'm getting and what I've done. I'm most suspicious of the full drive since that pops up twice and I did see one looks full. What's a good way to reduce what's on it?- or.. what else... (2 Replies)
Discussion started by: Stellaman1977
2 Replies
LEARN ABOUT REDHAT
install-netsync
install-netsync(1) General Commands Manual install-netsync(1)
NAME
install-netsync - reads or sets the Network Preferences information on a Palm Device
SYNOPSIS
install-netsync -p /dev/pilot -e -n <hostname> -i <ip> -m <netmask>
DESCRIPTION
install-netsync allows the user to read or change the Network Preferences stored on the Pilot
OPTIONS
-p --port <port>,
Use device file port to communicate with the Palm handheld device. If this is not specified, will look for the $PILOTPORT environ-
ment variable. If both are not found, will fall back to /dev/pilot.
-h --help
Display help synopsis for install-netsync
-v --version
Display version of install-netsync
-e --enable
Enable the LanSync operation (instead of local HotSync)
-n --name <hostname>,
Sets the hostname of the remote machine you wish to connect to. This is not the hostname of the Palm device itself
-i --ip
Set the IP address of the remote machine you wish to connect to. This is not the IP address of the Palm device itself
-m --mask
Set the netmask of the remote machine you wish to connect to. This is not the netmask address of the Palm device itself
USAGE
The program will connect to a target Palm handheld device, and read or set the Network Preferences information specified or display the
Network Preferences stored on the Palm device
KNOWN BUGS
install-netsync has no known bugs.
REPORTING BUGS
Report bugs at http://bugs.pilot-link.org/
AUTHOR
install-netsync was created from the original install-user
application originally written by D. Jeff Dionne <jeff@RyeHam.ee.ryerson.ca>, and was split it out into a separate conduit by JP Rosevear
<jpr@ximian.com>
Free Software Foundation Palm Computing Device Tools install-netsync(1)