12-26-2014
Thanks for your reply
ok have just finished installing os on my other C8000, minimal hardware, DID NOT select DCHP option for network, manually entered ip address for machine as 192.168.1.18, gateway as 192.168.1.1 which is the value I use for the ethernet to wifi adapter that I have set up previously to connect to wifi on ethernet hardware I own ( this is the value I use on my SGI Octane when using this adaptor) it boots into the CDE Desktop and I can operate everything fine (prev. if I select DCHP , network settings get assigned and I get an error about desktop messaging system and I cannot log in in anything but failsafe mode) however if I start up mozilla , it cannot find any pages, keeps saying good web address cannot be found , please check and try again. on the other computer , after fiddling with network settings, I could get mozilla to load pages BUT it would then come up with desktop messaging system error and I would have to log back in in failsafe mode and could run mozilla ok but obviously could not get to a standard CDE session. In summary CAN EITHER HAVE A STANDARD CDE LOGIN WITH NO ERROR ABOUT MESSAGING SYSTEM BUT NO INTERNET RUNNING MOZILLA.............OR .............. ONLY A FAILSAFE LOGIN BECAUSE OF DESKTOP MESSAGING ERROR HOWEVER MOZILLA DOES INFACT WORK. BUT........... NOT BOTH WORKING AT SAME TIME.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi People!
I've just got a HP-UX system dumped on me. I've started it, followed all the install/setup questions, and everything was going ok, right upto when going into the desktop enviroment I got the message "The Desktop Messaging System Could Not Be Started".
Now I've checked the... (8 Replies)
Discussion started by: cpiuk
8 Replies
2. UNIX for Dummies Questions & Answers
Hello folks, had a question.
I was trying to install sudotool on HP -UX 11i.
I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box
how do i install it??
do i need to run "swinstall" menu and then choose from there?
THanks!
karthik (1 Reply)
Discussion started by: karthikosu
1 Replies
3. HP-UX
Hi Experts
I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error.
ENTRY_INIT failed, status = -4: Unrecoverable hardware error
(followed by a hex dump)
I have re-tried many times and on one occasion successfully got through to CD... (4 Replies)
Discussion started by: C3000
4 Replies
4. HP-UX
Hey,
i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write
BOot P1
P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said:
P0 scsiA.6 HP73.4MAT3073NP
P1 ide.1 ... (2 Replies)
Discussion started by: numx
2 Replies
5. UNIX for Advanced & Expert Users
Hello All,
I am getting " The DT messaging system could not be started" message when wants to login as root on a box running on tru64 5.1A.
/etc/hosts is ok.
when i see in .dt/errorlog it shows message server could not be started.
Thanks for help.
Awadhesh (2 Replies)
Discussion started by: Awadhesh
2 Replies
6. Solaris
hi all,
I want to install iplanet messaging service in solaris 10.
if it is possible plz send the procedure for installation.its urgent plz
regards
spandan (2 Replies)
Discussion started by: spandhan
2 Replies
7. HP-UX
Hi there,
hope you can help since I'm a novice and playing with this machine to maybe one day use it with our non-profit art project (plantage9.de).
I have the proper media for itanium and everything seems okay, loads the DVD etc., until it halts without any progress for hours (see also image... (1 Reply)
Discussion started by: plantage
1 Replies
8. Red Hat
I have an application rpm which when installed is failing to get installed with error
error: Failed dependencies:
libc.so.6 is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.0) is needed by testSam-4.7.x86_64
libc.so.6(GLIBC_2.1) is needed by testSam-4.7.x86_64
... (1 Reply)
Discussion started by: rupeshkp728
1 Replies
9. Shell Programming and Scripting
Good Morning,
Users can no longer log into SunBlade 2500 Solaris 9 system (though root still can). Here's what I'm getting and what I've done. I'm most suspicious of the full drive since that pops up twice and I did see one looks full. What's a good way to reduce what's on it?- or.. what else... (2 Replies)
Discussion started by: Stellaman1977
2 Replies
LEARN ABOUT DEBIAN
ifscheme-mapping
IFSCHEME(8) Commands IFSCHEME(8)
NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS
-v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO
interfaces(5) ifup(8) ifdown(8)
DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)