Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Restarting/Resetting a USB Port? Post 302929385 by hicksd8 on Saturday 20th of December 2014 05:48:43 AM
Old 12-20-2014
Having read your post a few times I think that you may be going about this the wrong way. You shouldn't need to reset the USB port, the modem software (driver should take care of it.

Firstly, what operating system is it????

Do you definitely have the correct Conexant driver for that O/S?

A modem is a serial port device but in this case the serial port is a virtual one inside the USB driver on the host.

If the remote end hangs up, the local modem should detect carrier loss and, through the USB interface, notify it's host uSB driver, which in turn should signal to the O/S that the remote end has gone away. The local O/S responds by closing the session/process thereby clearing down the modem (virtual) port.

So do you have the right USB driver for your O/S?

and

Is the local modem configured to correctly report a loss of carrier (DCD signal)? See modem manual for that one.
 

10 More Discussions You Might Find Interesting

1. Solaris

network on solaris 10, through usb port...(urgent)

hi all, I have been trying to setup network on solaris10 from a long time but am unable to do so.. I tried it with the ethernet card i have(dfe -520tx) but since i was not able to find drivers for that particular device, i thought of using the usb mode to run network.. However am not able... (0 Replies)
Discussion started by: wrapster
0 Replies

2. AIX

How to connect PC's USB port to pSeries system?

Hello AIX Group Members, I have two systems: (1) IBM pSeries 640, 7026-B80. (2) A 5-month old HP laptop with Windows Vista. It has no serial port and only has USB ports on it. My question are: How can I use the laptop as the p640's terminal? How can I make the connection? What type of cable... (4 Replies)
Discussion started by: aixlover
4 Replies

3. UNIX for Dummies Questions & Answers

USB port is disabled using BIOS, I want to enable it

Hi, I have PC with Linux OS RHEL3 and USB port is disabled from BIOS. BIOS access is protected using password. But, I have root access. Now, how can I enable USB port using root access? Is there any trick that I can do using root access that can enable USB port once my PC has booted up? (3 Replies)
Discussion started by: gydave
3 Replies

4. UNIX for Advanced & Expert Users

how to watch the usb port

I want to watch the USB ports. If any device is connected to the USB port I want to take the name of the device and I want to log the device name. how to watch all the USB ports. How to find the device is connected in which usb port. (1 Reply)
Discussion started by: ungalnanban
1 Replies

5. Ubuntu

driver for external drive case on usb port

Hi I have to buy my selfe external case for hdd but I don't know whether my ubuntu linux, needs some driver to be able to work with this device or it has inside of itselfe this driver ? rhx for help. (1 Reply)
Discussion started by: presul
1 Replies

6. Shell Programming and Scripting

Restarting USB Bluetooth Dongles immediately

Hi @all, i am currently having a Problem: I want to restart 2 USB Bluetooth Dongles from the shell at the same time. It is very important that they are restarted nearly simultaneously, so that their clocks are starting to run at the same time. At the moment i am using a command called... (3 Replies)
Discussion started by: cabrix
3 Replies

7. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies

8. Solaris

Solaris 11.2 does not assign serial port to 3g usb modem?

In ubuntu etopic i create this udev rules for prolink 3g usb modem: SUBSYSTEM=="block", SUBSYSTEM=="scsi", ATTRS{idVendor}=="1e0e", ATTRS{idProduct}=="f000", ACTION=="add", RUN+="/sbin/modprobe usbserial Vendor=0X1e0e Product=0Xf000" After plugging the usb modem, ubuntu assigns the ports... (4 Replies)
Discussion started by: shamsat
4 Replies

9. Shell Programming and Scripting

USB port events linstening

Hi everybody! :) I am a complete newbie. :D Is it possible to write a script (shell or python) to listen to usb port event and to notify me every time an usb storage key is plugged or ejected? I want it to echo the device to mount (eg. /dev/sdb). I wrote an udev rule wich runs a script after... (1 Reply)
Discussion started by: manuhexadec
1 Replies

10. Linux

Connect from USB to serial port of switch

I have someone wanting to connect to the serial management port of a switch from a PC running CentOS6. The management port on the switch is apparently baud 9600, 8 data bits, 1 stop bit & no parity They have plugged in a cable to connect and the output from lsusb is:-Bus 001 Device 001: ID... (7 Replies)
Discussion started by: rbatte1
7 Replies
BAYCOM(9)						      Kernel Reference Guide							 BAYCOM(9)

NAME
baycom - amateur (AX.25) packet radio network driver for baycom modems SYNOPSIS
#include <linux/baycom.h> #include <linux/hdlcdrv.h> DESCRIPTION
The driver currently supports three different modems: ser12, par96 and par97. ser12 This is a very simple 1200 baud AFSK modem. The modem consists only of a modulator/demodulator chip, usually a TI TCM3105. The computer is responsible for regenerating the receiver bit clock. The modem connects to a serial port, hence the name. Since the serial port is not used as an async serial port, the kernel driver for serial ports cannot be used, and this driver only supports standard serial hardware (8250, 16450, 16550). par96 This is a modem for 9600 baud FSK compatible to the G3RUH standard. The modem does all the filtering and regenerates the receiver clock. Data is transferred from and to the PC via a shift register. The shift register is filled with 16 bits and an interrupt is signalled. The PC then empties the shift register in a burst. This modem connects to the parallel port, hence the name. par97 This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem is protocol compatible to par96, but uses only three low power ICs and can therefore be fed from the parallel port and does not require an additional power supply. IOCTL CALLS
The ioctl calls follow the implementation in the hdlcdrv. BAYCOMCTL_GETMODEMTYPE returns the modem type (i.e. ser12 or par96) and the options in effect (currently only the source of the DCD signal) BAYCOMCTL_SETMODEMTYPE sets the modem type and the options. Only superuser can do this. BAYCOMCTL_GETDEBUG return some debugging values. Not always available. SEE ALSO
baycom (9), soundmodem (9), linux/drivers/net/hdlcdrv.c, AUTHOR
baycom was written by Thomas Sailer, HB9JNX/AE4WA, (t.sailer@alumni.ethz.ch). Linux 2.1.x 2 October 1996 BAYCOM(9)
All times are GMT -4. The time now is 07:46 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy