12-01-2014
This is exactly how it's done. Why do you want to change it?
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
im kind alost. i beleave its a sed command. but i cant seem to find it in my book. can someone point me in the write direction.
i know this is extreamly sloppy. but this is what i did untill i can figure out how to manipulate the filename namespace.
an ls on the directory where this would run... (2 Replies)
Discussion started by: Optimus_P
2 Replies
2. Shell Programming and Scripting
hi all
need your help.
I am wrting a script that will load data into the table.
then on another load will append the data into the existing table.
Regards
Ankit (1 Reply)
Discussion started by: ankitgupta
1 Replies
3. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
4. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
5. Shell Programming and Scripting
Hi All,
I am working on nawk script, has the small function which prints the output on the screen.Am trying to print/append the same output in a file.
Basically nawk script should print the output on the console/screen and as well it should write/append the same result to a file.
script :... (3 Replies)
Discussion started by: Optimus81
3 Replies
6. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
7. UNIX for Dummies Questions & Answers
Hello, on my hostserver i see one VPS of mine got load of 200.00 and netstat nothing (not a single blank line on netstat command) after some time, netstat started showing connections, but i see no excessive IP connections.
tail -f /var/log/httpd/access_log shows no activity
/var/log/messages ;... (1 Reply)
Discussion started by: postcd
1 Replies
8. Shell Programming and Scripting
Hi, i want to add a line at the beginning of every file in a directory.
perl -i.bkp -p -e 'print "#include /verif/pdd1/exu/sxs/6sTest/reset/dfu/top_level.reset\n" if $. == 1' *.reset
But this command is updating only the first file in the directory. I think this is because $. is not resetting... (3 Replies)
Discussion started by: twistedpair
3 Replies
load(8) System Manager's Manual load(8)
Name
load - down-line load software to a target node
Syntax
/etc/load [ node ]
Description
The command loads software to an unattended target node. The target node is loaded by the host that executes the command.
The command requires the identification of the service circuit over which the load is performed, the Ethernet hardware address of the tar-
get node, and the service password needed to gain access to the target. This information is included in the nodes database entry for the
target node. A node entry is defined with the command. For further information, see The node is the name or address of the target node.
A node name consists of from one to six alphanumeric characters. For single networks, a node address consists of a decimal integer
(1-1023). For multiple networks, a node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
Options
-p Uses the specified service and password (next arguments) in accessing the target node. You can omit a target node's service and pass-
word from the nodes database for security reasons, but you must then specify the service and password in the command line by using the
option.
Examples
# /etc/load bangor -p 130fe
This command causes node to be loaded by the ULTRIX host node executing the command. The ULTRIX host uses the load files specified in the
nodes database entry for node to perform the load.
See Also
addnode(8), ccr(8), getnode(8), mop_mom(8), remnode(8), trigger(8)
Guide to Local Area Transport Servers
load(8)