11-15-2014
Quote:
Originally Posted by
hicksd8
If you've not already done it, I would disable "quick boot" in the BIOS to force the machine to test all it's memory during POST.
The A1+B1 slot configuration each side is correct according to the book.
Perhaps there's a faulty DIMM. If so, with "quick boot" disabled POST should crash and tell you something.
I didn't see option "quick boot" in BIOS system. Do you have any solutions for this?
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everybody
i am trying to telnet to sun server from win xp machine but getting message "x21 error connection closed by remote user". i had make changes in /etc/default/login & /etc/fuser file still i have not getting telnet access. my win xp machines ip is 10.205.121.177 & sun server ip is... (1 Reply)
Discussion started by: pshelke
1 Replies
2. Solaris
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies
3. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
4. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
5. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
6. Ubuntu
Hi
I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them.
I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output.
The issue i have is that when i configure the network... (0 Replies)
Discussion started by: kaf3773
0 Replies
7. Solaris
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Discussion started by: ssabet
5 Replies
8. Solaris
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT FREEBSD
nvram
NVRAM(4) BSD Kernel Interfaces Manual NVRAM(4)
NAME
nvram -- non-volatile RAM
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device nvram
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
nvram_load="YES"
DESCRIPTION
The nvram driver provides access to BIOS configuration NVRAM on i386 and amd64 systems.
PC motherboard uses a small non-volatile memory to store BIOS settings which is usually part of its clock chip and sometimes referred as
``CMOS SRAM''. This driver exposes bytes 14 through 128 of the NVRAM, or a total of 114 bytes, at offset zero of the device file /dev/nvram.
This driver is useful for cloning machines that shares the same hardware configuration and need same BIOS setting tweaks.
IMPLEMENTATION NOTES
The BIOS NVRAM's bytes 16 through 31 are checksummed at byte 32. This driver does not take care for these checksums.
EXAMPLES
Backup existing BIOS NVRAM to nvram.bin:
dd if=/dev/nvram of=nvram.bin
Restore BIOS NVRAM from nvram.bin:
dd if=nvram.bin of=/dev/nvram
SEE ALSO
dd(1)
HISTORY
The nvram device driver first appeared in FreeBSD 6.4.
AUTHORS
The nvram device driver was written by Peter Wemm. This manual page was written by Xin LI.
BSD
February 8, 2010 BSD