11-14-2014
Hi, This error was while installing DAQ...
I just run ./configure in the DAQ directory.
7 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
i'm following the, "How to setup and secure Snort, MySQL and Acid on FreeBSD 4.6 Release" off of the snort.org website.
in the documentation it says snort should be installed through the following:
-----
make -DWITH_MYSQL -DWITH_FLEXRESP ; make install
-----
later it says to do the... (13 Replies)
Discussion started by: xyyz
13 Replies
2. BSD
Im trying to gather some info to set up snort on openbsd 3.2, has anyone out there managed to get it up and running ? My initial attempts seem to be quite below par (4 Replies)
Discussion started by: malcontent
4 Replies
3. Linux
Hi,
can anybody know snort port no in linux, (1 Reply)
Discussion started by: manoj.solaris
1 Replies
4. Cybersecurity
I have been asked to place 2 (1 NTOP & 1 SNORT) boxes within our network as part of our tool kit for network monitoring and Intrusion detection. Out network is very simplistic and it layed out like this:
internet
|
|
Cisco 1811 Router (8x Layer 2 switch ports)
... (0 Replies)
Discussion started by: metallica1973
0 Replies
5. Cybersecurity
Is it possible to rule out in alert all HTTPS traffic or rule out all the HTTPS trafic from the alerts on snort ? (3 Replies)
Discussion started by: drd0spt
3 Replies
6. Solaris
Not very helpful to say the least. Seems to read the flar file and go through the upgrade and then come up with this error.
Any ideas? (1 Reply)
Discussion started by: psychocandy
1 Replies
7. UNIX for Beginners Questions & Answers
I've been trying to get Snort running on my lab network, but haven't been having much luck.
I installed Snort 2.9.14 on both Windows 10 & Ubuntu 18.04 (Running in VirtualBox 5.2.22). I seems to have the snort.conf file set up correctly in both environments, because when I test snort in either... (1 Reply)
Discussion started by: bodisha
1 Replies
LEARN ABOUT REDHAT
mdeltree
mdeltree(1) General Commands Manual mdeltree(1)
Name
mdeltree - recursively delete an MSDOS directory and its contents
Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.
Description
The mdeltree command is used to delete an MS-DOS file. Its syntax is:
mdeltree [-v] msdosdirectory [msdosdirectories...]
Mdeltree removes a directory and all the files and subdirectories it contains from an MS-DOS filesystem. An error occurs if the directory
to be removed does not exist.
See Also
Mtools' texinfo doc
Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips mtools.dvi
* To generate a html copy, run:
./configure; make html
A premade html can be found at: `http://mtools.linux.lu' and also at: `http://www.tux.org/pub/knaff/mtools'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
mtools-3.9.8 02Jun01 mdeltree(1)