11-13-2014
Did you use ECC memory?
Did you use IBM memory, or something off-the-shelf?
What are the BIOS memory settings?
Either you used the wrong memory, the BIOS settings are incorrect, or your memory is bad.
And IBM servers tend to work only with IBM memory. You might get them to work with non-IBM memory, but you're lucky if it works.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everybody
i am trying to telnet to sun server from win xp machine but getting message "x21 error connection closed by remote user". i had make changes in /etc/default/login & /etc/fuser file still i have not getting telnet access. my win xp machines ip is 10.205.121.177 & sun server ip is... (1 Reply)
Discussion started by: pshelke
1 Replies
2. Solaris
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies
3. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
4. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
5. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
6. Ubuntu
Hi
I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them.
I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output.
The issue i have is that when i configure the network... (0 Replies)
Discussion started by: kaf3773
0 Replies
7. Solaris
cat note
Hi Sun Solaris Experts,
When I try to install Solaris 8 10/00 OS via the Solaris 8 Installation Disk on our Sun Fire V490 Server using the command , I get:
boot: cannot open kernel/sparcv9/unix
which means it can't find the unix kernel file on the installation disk .
By the way, I... (5 Replies)
Discussion started by: ssabet
5 Replies
8. Solaris
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
reboot(8) System Manager's Manual reboot(8)
NAME
reboot - Restarts the machine
SYNOPSIS
/usr/sbin/reboot [-dlnq]
DESCRIPTION
When the system is running and multiple users are logged in, use the shutdown -r command to perform a reboot operation. If no users are
logged in, use the reboot command.
The reboot command normally stops all running processes, syncs the disks, logs the reboot, and writes a shutdown entry in the login
accounting file, /var/adm/wtmp.
The reboot command uses the sync call to synchronize the disks, and to perform other shutdown activities such as resynchronizing the hard-
ware time-of-day clock. After these activities, the system reboots. By default, the system starts and the file systems are automatically
checked. If the start-up activities are successful, the system comes up in the default run-level.
You must have root privileges to use this command. Using the -n flag can result in file system damage.
FLAGS
Generates a crash dump of the system before halting it. Can be used with any of the other flags. Does not log the reboot using syslog
Does not sync the disks or log the reboot using syslog Performs a quick reboot without first shutting down running processes; does not log
the reboot using syslog
EXAMPLES
To enable the default reboot action, enter: reboot This command causes the system to stop all running processes, sync the disks, log the
shutdown, and perform other routine shutdown and reboot activities. To shut down the system without logging the reboot, enter: reboot -l
This command shuts down the system and performs all shutdown and reboot activities, except logging the shutdown. To reboot the system
abruptly, enter: reboot -q This command reboots the system abruptly without shutting down running processes.
FILES
Specifies the command path Specifies the login accounting file Specifies the path of the syslog daemon
RELATED INFORMATION
Commands: fsck(8), halt(8), init(8), savecore(8) shutdown(8), syslogd(8)
Functions: reboot(2), sync(2), syslog(3) delim off
reboot(8)