11-12-2014
@jlliagre, but can a Solaris 11 support a Solaris 8 branded zone? Can you see my point? Back when Sun was still around I was forced to use have both a Solaris 10 and Solaris 11 env. to handle all of my (then) container needs.
Just saying...
And personally, I still think it might be harder to get all of the "u" variations. But, I'm ok if that's not correct information.
10 More Discussions You Might Find Interesting
1. SuSE
Hi All,
Is there a max number of slabs that can be used per kernel module? I'm having a tough time finding out that kind of information, but the array 'node_zonelists' (mmzone.h) has a size of 5. I just want to avoid buffer overruns and other bad stuff.
Cheers,
Brendan (4 Replies)
Discussion started by: Brendan Kennedy
4 Replies
2. Ubuntu
Hi All,
Please let me know the following.
1) Does POSIX lib support kernel threads? if yes, please let me know what are the specific function calls used to create/manage kernel threads.
2) Is Posix scalable?
3) Does POSIX take the advantage of multiprocessor systems?
your help is much... (4 Replies)
Discussion started by: jayfriend
4 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I want to learn that all the family of x86 processors are supported by kernel.
I want to buy a board, which has VIA ESP10K processor and
CHIPSET: VIA CN333 north bridge & VIA VT8237R south bridge
Where can I find this?
Thanks. (5 Replies)
Discussion started by: yildiz.a
5 Replies
4. Solaris
Hi gurus
Could anybody tell me which file is read by kernel to set its default system kernal parameters values in solaris. Here I am not taking about /etc/system file which is used to load kernal modules or to change any default system kernal parameter value
Is it /dev/kmem file or something... (1 Reply)
Discussion started by: girish.batra
1 Replies
5. UNIX for Dummies Questions & Answers
Debian lenny uses the 2.6.26 kernel by default. Can I compile the most recent kernel from kernel.org and use it instead ? Will the new kernel be incompatible with other installed softwares ? (1 Reply)
Discussion started by: cyler
1 Replies
6. Red Hat
I upgraded from 2.6.32 to the 2.6.37.4 kernel and i 'm now booted from the new kernel .. but the size of the root file system / is increased substantially due to /usr/src .. and the new kernel is working fyn for us .. so i would like to remove the older kernel .. i tried to remove the 2.6.32... (6 Replies)
Discussion started by: fugitive
6 Replies
7. UNIX for Dummies Questions & Answers
Hi there,
I have a Debian Squeeze server.
How can I check if my kernel was compiled with NFS server support?
Extra question: if it is not, how do I enable NFS support in my kernel?
Thanks for your help.
Santiago (3 Replies)
Discussion started by: chebarbudo
3 Replies
8. Ubuntu
Does anyone know at which kernel version support for Phenom II x6 first appeared? (7 Replies)
Discussion started by: Varsel
7 Replies
9. Linux
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Discussion started by: gacanepa
0 Replies
10. IP Networking
Hello, i tried to enable IPv6 networking and after service network restart i seen these messages:
FATAL: Error inserting ipv6 (/lib/modules/2.6.18-348.16.1.el5.028stab108.1/kernel/net/ipv6/ipv6.ko): Device or resource busy
CRITICAL : Kernel is not compiled with IPv6 support
Bringing up... (6 Replies)
Discussion started by: postcd
6 Replies
LEARN ABOUT MOJAVE
zprint
ZPRINT(1) BSD General Commands Manual ZPRINT(1)
NAME
zprint -- show information about kernel zones
SYNOPSIS
zprint [-cdhlLstw] [name]
DESCRIPTION
zprint displays data about Mach zones (allocation buckets). By default, zprint will print out information about all Mach zones. If the
optional name is specified, zprint will print information about each zone for which name is a substring of the zone's name.
zprint interprets the following options:
-c (Default) zprint prints zone info in columns. Long zone names are truncated with '$', and spaces are replaced with '.', to allow
for sorting by column. Pageable and collectible zones are shown with 'P' and 'C' on the far right, respectively. Zones with pre-
posterously large maximum sizes are shown with '----' in the max size and max num elts fields.
-d Display deltas over time, showing any zones that have achieved a new maximum current allocation size during the interval. If the
total allocation sizes are being displayed for the zones in question, it will also display the deltas if the total allocations
have doubled.
-h (Default) Shows headings for the columns printed with the -c option. It may be useful to override this option when sorting by
column.
-l (Default) Show all wired memory information after the zone information.
-L Do not show all wired memory information after the zone information.
-s zprint sorts the zones, showing the zone wasting the most memory first.
-t For each zone, zprint calculates the total size of allocations from the zone over the life of the zone.
-w For each zone, zprint calculates how much space is allocated but not currently in use, the space wasted by the zone.
Any option (including default options) can be overridden by specifying the option in upper-case; for example, -C overrides the default option
-c.
DIAGNOSTICS
The zprint utility exits 0 on success, and >0 if an error occurs.
SEE ALSO
ioclasscount(1), lsmp(1), lskq(1),
Mac OS X 2 May 2016 Mac OS X