11-10-2014
read -t always returns bad options
As mentioned previously
read -t returns bad options.
Kindly suggest some alternate.
10 More Discussions You Might Find Interesting
1. HP-UX
How can I kick a user out after being idle for a certain amount of time, would prefer not to use scripts, will TMOUT work on HP-UX? (5 Replies)
Discussion started by: csaunders
5 Replies
2. Solaris
Hello everyone
I am a new one,I want to know how to get the solaris force the loginer out if he do not in a time
thanks (4 Replies)
Discussion started by: lyh003473
4 Replies
3. Shell Programming and Scripting
I want to prompt a user for input but I want it to timeout after a specified time if no response is given. I tried the sleep command but this does not work. I am using ksh.
Thanks. (10 Replies)
Discussion started by: rello
10 Replies
4. Shell Programming and Scripting
any idea on how to timeout the read statement for ksh?
for bash u can use read -t option
-t timeout
Cause read to time out and return failure if a complete
line of input is not read within timeout seconds. This
option has ... (2 Replies)
Discussion started by: ashterix
2 Replies
5. Shell Programming and Scripting
I have a script that at some point will ask the interactive user a question:
#!/bin/ksh
echo "What is your access code?"
read ans
...
Sometimes this script is run by other scripts and there are no interactive users. The script then hangs on the "read" command, waiting for a user response... (5 Replies)
Discussion started by: rm-r
5 Replies
6. Red Hat
I have a RHEL 2.1 machine that I am trying to get to mount a remote nfs filesystem. Both servers have 2 network interfaces. My linux machine can mount the filesystem through one interface with no problems but if I switch over and try to mount it through the other interface using a totally... (1 Reply)
Discussion started by: darren.wyatt
1 Replies
7. Shell Programming and Scripting
hello every one ,
this is my first participation in the forum , I hope it'll be a good start
within a script I would like to put some code to read i\p from standard i\p using read command if it reads Y it will terminate the script if it reads N it will continue execution , if no i\p is... (2 Replies)
Discussion started by: Blue_shadow
2 Replies
8. Boot Loaders
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
9. Linux
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
10. UNIX for Advanced & Expert Users
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Discussion started by: wljackhero
0 Replies
LEARN ABOUT LINUX
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M)
NAME
addbadsec - map out defective disk blocks
SYNOPSIS
addbadsec [-p] [ -a blkno [blkno...]] [-f filename] raw_device
DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis,
but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be
fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI
drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software
remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping.
It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block
occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup.
OPTIONS
The following options are supported:
-a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be
quoted and block numbers should be separated by white space.
-f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file.
-p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option
cannot be used to print the hardware map.
OPERANDS
The following operand is supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec,
diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to
label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 addbadsec(1M)