11-03-2014
Remember that an RS232 port is NOT p'n'p so if there is any interruption then problems could be had.
You have learnt SW from Corona688 and HW pitfalls from me.
The real world is that your connection may be interrupted by a third party event beyond your control, (example a major underground cable assembly being damaged during roadworks), which shuts you off from access to the remote scales...
Not sure how you are going to cater for long time interruptions unless you can get the scales to store its data locally then do a dump to your machine when everything returns back to normal...
BTW these tests should initially be done locally before even attempting ANY remote tests.
This is a good starting point to find out more about the old serial port:-
RS-232 - Wikipedia, the free encyclopedia
10 More Discussions You Might Find Interesting
1. Linux
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies
2. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
3. Programming
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Discussion started by: ExDes
2 Replies
4. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
5. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
6. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Shell Programming and Scripting
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Discussion started by: yashwantkumar
1 Replies
9. Web Development
I need to set a serial port to 9600 7E1. How do I accomplish this?
I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT DEBIAN
mojomojo::formatter::wikipedialink
MojoMojo::Formatter::WikipediaLink(3pm) User Contributed Perl Documentation MojoMojo::Formatter::WikipediaLink(3pm)
NAME
MojoMojo::Formatter::WikipediaLink - Linked Wikipedia by writing {{wikipedia:<lang> <word>}}
DESCRIPTION
Normally, to hyperlink to the Wikipedia, you'd write:
[wikipedia Hello](http://en.wikipedia.org/wiki/Hello)
This plugin lets you write just
{{wikipedia Hello}}
not just Link to Wikipedia in English page, you can use many languages
{{wikipedia:ja a~XXa~XXa~XXa~XXa~XX}}
{{wikipedia:fr Salut}}
Actually, if you wrote this without a language ex.{{wikipedia Foo}}, select location of Wikipedia Link is getting default-language setting
of MojoMojo.
METHODS
format_content_order
The WikipediaLink formatter has no special requirements in terms of the order it gets run in, so it has a priority of 17.
format_content
Calls the formatter. Takes a ref to the content as well as the context object.
process
Here the actual formatting is done.
SEE ALSO
MojoMojo and Module::Pluggable::Ordered.
AUTHORS
Dai Okabayashi, "bayashi at cpan . org"
LICENSE
This library is free software. You can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.14.2 2010-05-23 MojoMojo::Formatter::WikipediaLink(3pm)