There doesn't seem to be a relation between laptop-1 or laptop_fred and the MAC address given. So how should any command/program/script select 192.168.0.10 instead of 192.168.0.1 to place into your variable?
---------- Post updated at 11:58 ---------- Previous update was at 11:54 ----------
Hi sir,
i want to make such programe which takes MAC(Ethernet) address of any host & give me its IP address.......
but i'm nt getting that how i can pass the MAC address to Frame........
Please give me an idea for making such program...
Thanks & regards
Krishna (3 Replies)
Hi
I need to write a bash shell script. I have two separate text files. One file contains a list of MAC addresses taken from a network scan, the other contains a list of MAC addresses for our currently-managed devices. How can I compare these two files, and output a list of addresses that have... (6 Replies)
Hi everyone.
I'm looking for a way to extract the video card properties (Name, Driver version, amount of vram). I've managed to deal with nVidia cards, but nothing came for ATI/AMD cards and other kind of chipsets. Can someone point a way to do this?
Thanks. (4 Replies)
Hi there
I lost connectivity to one of our remote systems and when I checked the messages log I found the following:
Aug 10 23:42:34 host xntpd: time reset (step) 1.681729 s
Aug 16 13:20:51 host ip: WARNING: node "mac address" is using our IP address x.x.x.x on aggr1
Aug 16 13:20:51 host... (9 Replies)
I'm having trouble getting my WIFI card to work. It's Device ID is :0c:00.0 0280: 14e4:4315 (rev 01). My OS is BT5. The card works with Lucid just fine. I've gone to the Hardware drivers to try and download it but when I try I always get this:
SystemError: installArchives()failedI've gone to... (2 Replies)
I have hp dv6 and dv7 notebook pcs on which I want to upgrade the wifi cards but when I install the new cards and boot them, the they won't even boot to the bios and they both give me the same error: "104-Unsupported wireless network device detected. System Halted. Remove device and restart." When... (1 Reply)
After installing the latest version of Kali on my Lenovo S21E laptop, I cannot access the internet.
wlan0 does not show up in ifconfig and I cannot connect to the internet.
If you need any other additional information, I will provide it. Thank you kindly. (8 Replies)
four interfaces with ifconfig
all interfaces have the same mac. If is not set for unique.
but it still works.
what difference does it make to have all macs the same or different? (4 Replies)
Hy every body,
Unfortunately and without success, i want to write a bash script who maps a known IP addess to a known MAC address using iptables and for the FORWARD chain.
Within the DHCP server, i have assigned a fixed IP address to all clients based on their MAC addresses of their... (11 Replies)
Discussion started by: hermouche
11 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)ifsysctl(8)sysconfig December 2009 IFNDP-PROXY(5)