10-23-2014
Thanks wisecracker -
Which one is NO ? Both
Those parameters you display seem to be /dev/ttyS0 not the scales. Correct
I'll see what I can do, and keep you posted
10 More Discussions You Might Find Interesting
1. Linux
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Discussion started by: arunchaudhary19
16 Replies
2. Solaris
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
Discussion started by: smartgupta
1 Replies
3. Programming
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Discussion started by: ExDes
2 Replies
4. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
5. UNIX for Dummies Questions & Answers
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Discussion started by: dotancohen
2 Replies
6. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
7. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
8. Shell Programming and Scripting
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Discussion started by: yashwantkumar
1 Replies
9. Web Development
I need to set a serial port to 9600 7E1. How do I accomplish this?
I've tried every combination, with no luck. (6 Replies)
Discussion started by: Meow613
6 Replies
10. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT REDHAT
perlivp
PERLIVP(1) Perl Programmers Reference Guide PERLIVP(1)
NAME
perlivp - Perl Installation Verification Procedure
SYNOPSIS
perlivp [-p] [-v] [-h]
DESCRIPTION
The perlivp program is set up at Perl source code build time to test the Perl version it was built under. It can be used after running:
make install
(or your platform's equivalent procedure) to verify that perl and its libraries have been installed correctly. A correct installation is
verified by output that looks like:
ok 1
ok 2
etc.
OPTIONS
-h help
Prints out a brief help message.
-p print preface
Gives a description of each test prior to performing it.
-v verbose
Gives more detailed information about each test, after it has been performed. Note that any failed tests ought to print out some
extra information whether or not -v is thrown.
DIAGNOSTICS
o print "# Perl binary `$perlpath' does not appear executable.
";
Likely to occur for a perl binary that was not properly installed. Correct by conducting a proper installation.
o print "# Perl version `$]' installed, expected $ivp_VERSION.
";
Likely to occur for a perl that was not properly installed. Correct by conducting a proper installation.
o print "# Perl @INC directory `$_' does not appear to exist.
";
Likely to occur for a perl library tree that was not properly installed. Correct by conducting a proper installation.
o print "# Needed module `$_' does not appear to be properly installed.
";
One of the two modules that is used by perlivp was not present in the installation. This is a serious error since it adversely affects
perlivp's ability to function. You may be able to correct this by performing a proper perl installation.
o print "# Required module `$_' does not appear to be properly installed.
";
An attempt to "eval "require $module"" failed, even though the list of extensions indicated that it should succeed. Correct by con-
ducting a proper installation.
o print "# Unnecessary module `bLuRfle' appears to be installed.
";
This test not coming out ok could indicate that you have in fact installed a bLuRfle.pm module or that the "eval " require "$mod-
ule_name.pm"; "" test may give misleading results with your installation of perl. If yours is the latter case then please let the
author know.
o print "# file",+($#missing == 0) ? '' : 's'," missing from installation:
";
One or more files turned up missing according to a run of "ExtUtils::Installed -> validate()" over your installation. Correct by con-
ducting a proper installation.
o print "# Perl header `$_' does not appear to be properly installed.
";
Correct by running h2ph over your system's C header files. If necessary, edit the resulting *.ph files to eliminate perl syntax
errors.
For further information on how to conduct a proper installation consult the INSTALL file that comes with the perl source and the README
file for your platform.
AUTHOR
Peter Prymmer
perl v5.8.0 2003-02-18 PERLIVP(1)