So you have a scale local to you that you can see and physically connect to? Correct
This would have to be connected to the serial port using a cable then? Yes? Correct
Does the scale require a Null Modem Cable or an Extension type? NO
The data I displayed was after connecting the scale to the computer with a serial cable.
Assuming the scale has RS232 transfer; what are the serial parameters
Can it be used in raw data transfer mode? Please Explain
I think my serial port(on board) is not working ......
because when I am running same code on two machines its working good....but when my system comes into picture ....it doesnt show any output comming from serial port..........
can anybody tell me how to configure my serial port.........or to... (16 Replies)
Hi,
I am working with solaris 9,SUN-Blade-100 and I want to communicate with the Serial port.To check whether the port is working or not.I write code and when I execute the file,then I got the output--
According to this,serial port is not found.can anyone please tell me how to configure the... (1 Reply)
I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows:
SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK);
write (SerialPort_Send, pCommandString, strlen (pCommandString));
... (2 Replies)
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing:
# dmesg | grep tty
console enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
... (2 Replies)
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
hello all,
please any one can provide me the shell script to write data to /dev/ttyS1
and read responce from /dev/ttyS1 and compare the responce to some string ..
thnxx
---------- Post updated at 03:35 PM ---------- Previous update was at 11:46 AM ----------
any body help me..
how do i... (1 Reply)
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
LEARN ABOUT FREEBSD
uplcom
UPLCOM(4) BSD Kernel Interfaces Manual UPLCOM(4)NAME
uplcom -- USB support for Prolific PL-2303/2303X/2303HX serial adapters driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device usb
device ucom
device uplcom
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
uplcom_load="YES"
DESCRIPTION
The uplcom driver provides support for various serial adapters based on the Prolific PL-2303, PL-2303X and PL-2303HX USB-to-RS232 Bridge
chips.
The device is accessed through the ucom(4) driver which makes it behave like a tty(4).
HARDWARE
The uplcom driver supports the following devices and adapters:
o ADLINK ND-6530 USB-Serial Adapter
o Alcatel One Touch 535/735 Phone
o Alcor AU9720 USB-RS232 Serial Adapter
o AlDiga AL-11U Modem
o Alltronix ACM003U00 Modem
o Anchor Serial adapter
o ATEN UC-232A
o BAFO BF-800 and BF-810
o Belkin F5U257
o BenQ S81 Phone
o Corega CG-USBRS232R Serial Adapter
o Cressi Edy (Seiko) Diving Computer
o ELECOM UC-SGT Serial Adapter
o HAL Corporation Crossam2+USB IR commander
o Hama USB RS-232 Serial Adapter
o Hamlet exagerate XURS232
o HP LD220 Point-Of-Sale (POS) Display
o IOGEAR UC-232A
o I/O DATA USB-RSAQ, USB-RSAQ2, USB-RSAQ3 and USB-RSAQ5
o iTegno WM1080A GSM/GFPRS Modem
o iTegno WM2080A CDMA Modem
o Leadtek 9531 GPS
o Micromax 610U Modem
o Microsoft Palm 700WX
o Mobile Action MA-620 Infrared Adapter
o Motorola Cables
o Nokia CA-42 Cable
o OTI DKU-5 cable
o Panasonic TY-TP50P6-S flat screen
o PLX CA-42 Phone Cable
o PLANEX USB-RS232 URS-03
o Prolific Generic USB-Serial Adapters
o Prolific Pharos USB-Serial Adapter
o RATOC REX-USB60
o Radio Shack USB Serial Cable
o Sagem USB-Serial Adapter
o Samsung I330 Phone Cradle
o Sandberg USB to Serial Link (model number 133-08)
o Sanwa KB-USB2 Multimeter cable
o Siemens/BenQ EF81, SX1, X65 and X75 Mobile Phones
o Sitecom USB-Serial Adapter
o SMART Technologies USB-Serial Adapter
o Sony QN3 Phone Cable
o Sony Ericsson Datapilot
o Sony Ericsson DCU-10 and DCU-11 (Susteen) USB Cables
o SOURCENEXT KeikaiDenwa 8 (with and without charger)
o Speed Dragon USB-Serial Cable
o Syntech CPT-8001C Barcode Scanner
o TDK UHA6400 and UPA9664 USB-PHS Adapters
o TRENDnet USB to Serial Converter (TU-S9)
o Tripp-Lite U209-000-R USB-Serial Adapter
o UIC HCR331 Magnetic Stripe Card Reader
o UIC MSR206 Magnetic Stripe Card Reader
o Willcom W-SIM DD PHS terminal.(WS002IN)
o YC-Cable USB-Serial Adapter
o Zeagle N2iTion3 Diving Computer
SEE ALSO tty(4), ucom(4), usb(4)HISTORY
The uplcom driver appeared in NetBSD 1.6. This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org> in April 2002.
BSD July 25, 2012 BSD