Sponsored Content
Full Discussion: Faulty parts in a frame
Special Forums Hardware Faulty parts in a frame Post 302921140 by rbatte1 on Wednesday 15th of October 2014 07:25:01 AM
Old 10-15-2014
You would need to confirm this with your hardware engineer and consider the redundancy in your frame. Do you have dual service processors? You don't tell us much about the machine (i.e. the model would be a useful start) so I can't give you any further guidance.



Robin
This User Gave Thanks to rbatte1 For This Post:
 

10 More Discussions You Might Find Interesting

1. Solaris

Faulty PSU - but its still working !?!

Hello We have a power supply in an x4100 (x86) and it seems to be faulty but it is still working!?! (this box only has one PSU). We are getting Orange flashing warning light on the front of the box and the LED labelled “rear PSu” is solid orange ...We don't seem to have had any syslog error... (8 Replies)
Discussion started by: hcclnoodles
8 Replies

2. Solaris

Replacing a faulty volume

Hi All, I replace a sub-mirror of a mirrored volume by using below command: #metadetach d10(mirror) d11(striped) #metattach d10 d13(other striped) With above process I successfully replaced a faulty volume. I want to knoow if the process I followed is right. Or if not, what... (5 Replies)
Discussion started by: naw_deepak
5 Replies

3. Solaris

fmadm faulty output

Hi everyone, I wanted to ask a question about fmadm and explorer outputs. Recently found out that an error shows up in fmadm saying "mb is faulty but still in service" so we took an explorer send to Oracle Support. Error led wasn't on but we didn't want to risk the probability. They came up... (1 Reply)
Discussion started by: royalliege
1 Replies

4. Solaris

Help with faulty Disk on Sun OS

Hi, Recently i came across a disk that seems to be faulty and need help. I have gathered some information by running below commands and any help on how to solve this will be great. # uname –a SunOS XYZ 5.7 Generic_106541-16 sun4u sparc SUNW,Ultra-4 #df -k Filesystem kbytes used... (3 Replies)
Discussion started by: phanidhar6039
3 Replies

5. HP-UX

Remove Faulty disk from HP-UX LVM VG

Requirement to remove a faulty mirrored disk from hp-ux LVM <root@pdwp1s>/etc # vgdisplay -v /dev/vg00 vgdisplay: Warning: couldn't query physical volume "/dev/dsk/c2t0d0": The specified path does not correspond to physical volume attached to this volume group vgdisplay: Warning: couldn't... (9 Replies)
Discussion started by: Shirishlnx
9 Replies

6. HP-UX

Remove faulty disk LV from VG

Hi, Have mirrored the primary disk to 3 . Server and OS: # uname -a HP-UX pdwp1s B.11.11 U 9000/800 118434630 unlimited-user license # model 9000/800/L3000-7x # strings /etc/lvmtab /dev/vg00 +F@< /dev/dsk/c1t2d0 /dev/dsk/c2t2d0 /dev/dsk/c2t0d0 But now I have only 1 disk... (5 Replies)
Discussion started by: Shirishlnx
5 Replies

7. HP-UX

FAULTY DISK replacement HP rx4640

Hello, I'm new to this forum and as you will see from my question I'm new to UNIX as well. One of our costumers has HP rx4640 running on UNIX with two 300GB hot-swappable disks that are mirrored. They reported to us that one of the disks is faulty and they want us to take care of it. Below is... (16 Replies)
Discussion started by: gjk
16 Replies

8. Shell Programming and Scripting

Incrementing parts of ten digits number by parts

I have number in file which contains date and serial number: 2013101000. The last two digits are serial number (00). So maximum of serial number is 100. After reaching 100 it becomes 00 with incrementing 10 which is day with max 31. after reaching 31 it becomes 00 and increments 10... (31 Replies)
Discussion started by: Natalie
31 Replies

9. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies

10. UNIX for Beginners Questions & Answers

Show faulty shows PS1 faulty

I plugged both power cables in both power supply. When I unplugged each power cable one by one, the SPARC T4-1 machine keep running. However, show faulty command shows below message. (I have also attached the picture of both power supply) -> show faulty Target ... (1 Reply)
Discussion started by: z_haseeb
1 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 12:48 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy