|
|
Sponsored Content
Special Forums
IP Networking
Routing problem : two interfaces one gateway
Post 302920497 by Corona688 on Thursday 9th of October 2014 04:11:33 PM
10-09-2014
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
2. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. Linux
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Discussion started by: bakunin
0 Replies
4. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
5. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
6. IP Networking
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Discussion started by: andresguillen
2 Replies
7. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
8. AIX
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Discussion started by: RonBowater
4 Replies
9. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
essidscan
ESSIDSCAN(8) Commands ESSIDSCAN(8) NAME
essidscan - scan for ESSID corresponding to available WLAN access points SYNOPSIS
In /etc/network/interfaces: mapping <interface> script essidscan DESCRIPTION
The essidscan utility is used to tell the ifup and ifdown utilities about the current SSID of the WLAN currently being accessed. It can be used to map the SSID name to an iface stanza. CONFIGURATION
A sample /etc/network/interfaces may look like this: mapping hotplug script /etc/network/essidscan map SSIDONE wlan-work map SSIDTWO wlan-work map HOME iface wlan-work inet dhcp wireless-key 1234-5678-9ABC-DEF0-1234-5678-9A wireless-keymode restricted iface HOME inet static address 192.168.2.4 netmask 255.255.255.0 gateway 192.168.2.1 wireless-essid HOME wireless-key s:somepassword wireless-keymode open iface DEFAULT inet dhcp FILES
/etc/network/interfaces the interfaces definition file /etc/network/run/ifstate a record of the current state of the interfaces, managed by ifup and ifdown SEE ALSO
interfaces(5) ifscheme(8) ifup(8) ifdown(8) AUTHORS
Tor Slettnes <tor@slett.net> ESSIDSCAN(8)