10-09-2014
this is the horstbox
there are 4 blue ethernet ports. i am sorry but i have no deep knowledge in ip.
the first lan port (wan0 interface) is connected to my home network like i noticed before. if i connect with putty to the router on a shell i can ping an internet address. so the traffic seems to go over the wan0 interface and the standard gateway 192.168.2.1. thats good and ok.
but if i connect another device on lan port 2 -4 (br0) it gets no ip address from dhcp. there is no connection to my home network.
i am not sure what is the solution to this problem because of my limited knowledge to ip.
but the solution to me should be that when i connect another device to lan port 2-4 (br0) it should get acces to my home network (dhcp, internet etc).
any ideas ?
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
2. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. Linux
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Discussion started by: bakunin
0 Replies
4. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
5. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
6. IP Networking
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Discussion started by: andresguillen
2 Replies
7. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
8. AIX
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Discussion started by: RonBowater
4 Replies
9. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
net.connect
Net.connect(3kaya) Kaya module reference Net.connect(3kaya)
NAME
Net::connect - Connect to a server
SYNOPSIS
NetHandle connect( Protocol proto, String server, Int port, Bool usetls=false, [String] certfiles=[] )
ARGUMENTS
proto The network protocol to use
server The hostname or IP address of the server to connect to (e.g. service.example.com , localhost or 192.168.20.25 )
port The network port to connect to
usetls If this is true, and the TLS library is available, then the connection will be encrypted. This parameter may be omitted and defaults
to false.
certs An optional list of certificate files for TLS encrypted connections. Each file should contain one or more PEM-encoded certificates
for a trusted certification authority. If this list is empty (the default), no certificate verification will be performed on encrypted con-
nections, which is insecure.
DESCRIPTION
Connect to a server (optionally using TLS). Returns a connection handle.
AUTHORS
Kaya standard library by Edwin Brady, Chris Morris and others (kaya@kayalang.org). For further information see http://kayalang.org/
LICENSE
The Kaya standard library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public
License (version 2.1 or any later version) as published by the Free Software Foundation.
RELATED
Net.NetHandle(3kaya)
Net.Protocol(3kaya)
Net.closeConnection(3kaya)
Net.recv(3kaya)
Net.shutdown(3kaya)
Net.send(3kaya)
Kaya October 2012 Net.connect(3kaya)