10-09-2014
"connect" how? What do you want sent from what to where? How will it manage to forward anything to anyone without a gateway?
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
2. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. Linux
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Discussion started by: bakunin
0 Replies
4. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
5. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
6. IP Networking
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Discussion started by: andresguillen
2 Replies
7. Solaris
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Discussion started by: sri243
1 Replies
8. AIX
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Discussion started by: RonBowater
4 Replies
9. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
route(8c) route(8c)
Name
route - manually manipulate the routing tables
Syntax
/etc/route [ -f ] [ -n ] command args ]
Description
The program is used to manipulate the network routing tables manually. However, normally it is not needed, as the system routing table
management daemon, should tend to this task.
The program accepts two commands: add, to add a route and delete, to delete a route.
All commands have the following syntax:
/etc/route command [ net | host ] destination gateway [ metric ]
In this syntax, destination is a host or network for which the route is to, gateway is the gateway to which packets should be addressed,
and metric is an optional count indicating the number of hops to the destination. The metric is required for add commands. It must be
zero if the destination is on a directly-attached network, and nonzero if the route utilizes one or more gateways.
When adding a route with metric 0, the gateway given is the address of this host on the common network, indicating the interface to be used
for transmission. Routes to a particular host are distinguished from routes to a network by interpreting the Internet address associated
with destination. The optional keywords net and host force the destination to be interpreted as a network or host, respectively. If the
destination has a local address part of INADDR_ANY, then the route is assumed to be to a network. Otherwise, it is presumed to be a route
to a host. If the route is to a destination connected via a gateway, the metric should be greater than 0. All symbolic names specified
for a destination or gateway are looked up first as a host name using If this lookup fails, is then used to interpret the name as that of a
network.
The command uses a raw socket and the SIOCADDRT and SIOCDELRT ioctls to do its work. As such, only the superuser can modify the routing
tables.
Options
-f Flushes the routing tables of all gateway entries. If is used with one of the commands described above, the tables are flushed prior
to the command's application.
-n Prevents attempts to print host and network names symbolically when reporting actions.
Restrictions
The change operation is not implemented. Therefore, you should first add the new route, and then delete the old one.
Diagnostics
add [host | network] %s: gateway %s flags %x"
The specified route is being added to the tables. The values printed are from the routing table entry supplied in the ioctl call. If the
gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically as
well as symbolically.
delete [ host | network] %s: gateway %s flags %x
The specified route is being deleted from the tables. The values printed are from the routing table entry supplied in the ioctl call. If
the gateway address used was not the primary address of the gateway (the first one returned by the gateway address is printed numerically
as well as symbolically.
%s %s done
When the flag is specified, each routing table entry that is deleted is indicated with a message of this form.
Network is unreachable
An attempt to add a route failed because the gateway listed was not on a directly-connected network. The next-hop gateway must be given.
not in table
A delete operation was attempted for an entry which was not present in the tables.
routing table overflow
An add operation was attempted, but the system was low on resources and was unable to allocate memory to create the new entry.
See Also
intro(4n), routed(8c)
route(8c)