i have a horstbox-router with the following configuration.
it has 4 ethernet ports from wich one (wan0) is configured as an external modem via dhcp. at this port/interface(wan0) it is connected with my home network (other switch).
this configuration results in the following routing table :
so the router has internal acces to internet and can use voip from lan port 1 (wan0) which is the connected with a cable to my home network.
but on the other lan-ports i don't have internet acces or even acces to my home network. because it has no default gateway ?!
what command can i use to connect the interfaces br0 and wan0. or is it possible to route the traffic from br0 to wan0 ?
thanks in advance
Last edited by gencaslan; 10-09-2014 at 04:42 PM..
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
My setup consists of a hardware node, which hosts several virtual machines (OpenVZ, to be precise). The hardware node has two network interfaces (<ifA>, <ifB>) connected to different subnets (<networkA>, <networkB>). I want to route the traffic of certain VEs over <ifB> while routing the other VEs... (0 Replies)
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Hi gurus of unix, I haved installed my openSolaris in a HP530,
Recently I use the following command
beadm destry opensolaris1
beadm destry opensolaris2
After That I reboot my Laptop.
Well when I go to my work I try to open my wireshark tool, but the option in GUI interface does not appear!!!... (2 Replies)
Hi,
I have two physical interfaces on a servers.
We have connected them to differerent subnets.
1) First interface:
10.158.49.87 to newtwork 10.158.49.0, its gateway is 10.158.49.1
(It is added as default gateway)
It is existing set up. It works well
2) Second interface:
... (1 Reply)
Hi .. we have two AIX 5.3 systems with a small client server app communicating over a TCP socket.
Box A has a single network interface where the server app (in Java) opens a well known port and waits for connections from Box B.
Box B has two network interfaces, X and Y. Interface X has the... (4 Replies)
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
ifscheme
IFSCHEME(8) Commands IFSCHEME(8)NAME
ifscheme - scheme control for network interfaces
SYNOPSIS
ifscheme [-v] [[-s] newscheme]
mapping <interface> script ifscheme-mapping
DESCRIPTION
ifscheme allows you to change network configuraton schemes or query the current scheme. It integrates with the ifup(8) command and inter-
faces(5). For example, you might use this program to configure a "home" scheme and a "work" scheme for a network device on a laptop. When
you move between home and work, a simple command can reconfigure your networking.
If you run the program with no parameters, it will tell what the current network scheme is.
The ifscheme-mapping utility is used to tell the ifup and ifdown utilities about the current scheme.
OPTIONS -v
--verbose
Run in verbose mode. This is passed in to the ifup and ifdown programs as well.
-l
--list list all schemes available/defined in /etc/network/interfaces.
newscheme
-s newscheme
--scheme newscheme
Change to a new network configuration scheme. When the scheme is changed, network interfaces that were using the old scheme will be
taken down and brought back up to use the new configuration scheme. -s or --scheme are mandatory if newscheme begins with a -.
CONFIGURATION
To make the program do anything useful when a scheme is selected, you must edit /etc/network/interfaces to add a mapping for the interface
(or interfaces) that can be controlled on a per-scheme basis. Suppose you want to control eth0 in this way. You might have an existing eth0
configuraton in there, such as:
auto eth0
iface eth0 inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
To change this so you can chose between static routing and dhcp, replace it with the following (it helps to ifdown the interface first).
auto eth0
mapping eth0
script ifscheme-mapping
iface eth0-home inet static
address 192.168.1.5
netmask 255.255.255.0
gateway 192.168.1.1
iface eth0-work inet dhcp
Now if you run "ifscheme home" and ifup the interface, you'll get the eth0-home configuration stanza. If you run "ifscheme work", it will
be changed to the eth0-work stanza. You can add additional stanzas as desired, but the label must always be of the form <hardware inter-
face>-<scheme name>.
If you have a second interface (perhaps a wireless network card on eth1), you can duplicate the above for that interface, changing the eth0
and the configuration details as appropriate, but remember to add an iface stanza for every scheme name for the second interface.
FILES
/etc/network/interfaces
the interfaces definition file
/etc/network/run/scheme
the current scheme
/etc/network/run/ifstate
a record of the current state of the interfaces, managed by ifup and ifdown
BUGS
All schemed interfaces will have the same scheme.
Any schemed interface which does not have an entry for the current scheme and is not configured when the scheme is changed will not be suc-
cessfully configured when it is brought up.
SEE ALSO interfaces(5)ifup(8)ifdown(8)DISTRIBUTION
Redistribution is subject to the GNU public license.
AUTHORS
Joey Hess <joey@kitenet.net>, Peter Wilson <pwilson@cs.hmc.edu>
IFSCHEME(8)