Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a... (3 Replies)
Setup a site to site VPN between two cisco routers.
One of the site locations is unable to access ports such as https://example.com:9001
How do I let them go into port 9001?
They can ssh, ftp, telnet and everything else.
Is this a VPN issue or ACL access issue?
I put
permit ip host... (0 Replies)
Hello,
I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue.
... (0 Replies)
Hi,
I am trying to establish vpn between my linux server and cisco asa at client side.
I installed openswan on my cent os.
Linux Server
eth0 - 182.2.29.10
Gateway - 182.2.29.1
eth1 - 192.9.200.75
I have simple IPtables Like
WAN="eth0"
LAN="eth1" (0 Replies)
Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? "
A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that... (0 Replies)
Hi all,
I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug.
Please suggest what may be the cause for the above mentioned issue.
Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not... (13 Replies)
Discussion started by: Circuits
13 Replies
LEARN ABOUT REDHAT
aggregate-ios
AGGREGATE-IOS(1) General Commands Manual AGGREGATE-IOS(1)NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short.
SYNOPSIS
aggregate-ios <source_config >optimised_config
DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std-
out.
OPTIONS
None.
DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr.
EXAMPLES
The following configuration fragment:
ip prefix-list AS65530 description Foo, Inc
ip prefix-list AS65530 permit 10.1.0.0/16
ip prefix-list AS65530 permit 10.2.0.0/16
ip prefix-list AS65530 permit 10.2.1.0/24
ip prefix-list AS65530 permit 10.3.0.0/16
ip prefix-list AS65531 description Bar.Com
ip prefix-list AS65531 seq 5 permit 192.168.1.0/24
ip prefix-list AS65531 seq 10 permit 192.168.2.0/24
ip prefix-list AS65531 seq 15 permit 192.168.0.0/19
is optimised as follows:
ip prefix-list AS65530 permit 10.1.0.0/16 le 24
ip prefix-list AS65530 permit 10.2.0.0/15 le 24
ip prefix-list AS65531 permit 192.168.0.0/19 le 24
SEE ALSO aggregate(1)HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>.
BUGS
All those in aggregate(1) and then some :)
Joe Abley 2000 November 27 AGGREGATE-IOS(1)