IPSec Openswan Site to Site VPN - Big Pain Post: 302919884

8 More Discussions You Might Find Interesting

1. Cybersecurity

IPSec - VPN using shared key

Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a...

2. IP Networking

port access to site to site VPN

Setup a site to site VPN between two cisco routers. One of the site locations is unable to access ports such as https://example.com:9001 How do I let them go into port 9001? They can ssh, ftp, telnet and everything else. Is this a VPN issue or ACL access issue? I put permit ip host...

3. IP Networking

IPSec VPN Routing

Hello, I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue. ...

4. IP Networking

How to establish site to site vpn - Linux machine and cisco asa?

Hi, I am trying to establish vpn between my linux server and cisco asa at client side. I installed openswan on my cent os. Linux Server eth0 - 182.2.29.10 Gateway - 182.2.29.1 eth1 - 192.9.200.75 I have simple IPtables Like WAN="eth0" LAN="eth1"

5. IP Networking

Does cisco 1921 router support site to site VPNs using IPSec?

Q: "Does Cisco 1921 router support,, act as an endpoint for, site to site VPNs using IPSec? If so, how many? " A: If you get the Cisco 1921/k9 with the security services bundle then it will have built in security features. Cisco, typically includes IP Sec tunnels I believe as part of that...

6. IP Networking

VPN IPSec Openswan

Hi all, I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (...

7. IP Networking

Best tool to monitor VPN IPSEC Tunneling

We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug. Please suggest what may be the cause for the above mentioned issue. Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity.

8. What is on Your Mind?

Is this site for me?

Hello, I am new here and my name is Robert. I was actually looking for a forums website where I can go with questions regarding Linux and embedded Linux applications. I am fairly new (6 months) to the world of Linux and embedded Linux applications and the the learning curve is steep. When I am not...

LEARN ABOUT DEBIAN

tgt-setup-lun

tgt-setup-lun(8)					      System Manager's Manual						  tgt-setup-lun(8)

NAME

       tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target

SYNOPSIS

       tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]

DESCRIPTION

       Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
       iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.

       The  script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
       tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.

EXAMPLES

       Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
       tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81

       Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
       tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82

       Create a target that uses /dev/sdb1 and allows connections from any initiator:
       tgt-setup-lun -d /dev/sdb1 -n my_target

       Display help:
       tgt-setup-lun -h

AUTHOR

       Written by Erez Zilber

REPORTING BUGS

       Report bugs to <stgt@vger.kernel.org>

COPYRIGHT

       Copyright (C) Voltaire Ltd. 2008.

																  tgt-setup-lun(8)