Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Hello,
I am very new to solaris so please bear with me. I have 2 machines in question. For both I am trying to get the HBA Card Hardware information such as:
HBA Model Name
HBA Firmware version
HBA Port details
HBA Driver details
First machine is a Solaris 10. When I execute fcinfo... (6 Replies)
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Dear all,
I have a new Oracle Blade X4-2B server, running Solaris 10.
The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing.
My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
LEARN ABOUT DEBIAN
srec_formatted_binary
srec_formatted_binary(5) File Formats Manual srec_formatted_binary(5)NAME
srec_formatted_binary - Formatted Binary file format
DESCRIPTION
This is the PDP-11 paper tape format, described in the DEC-11-GGPC-D PDP-11 "Paper Tape Software Programming Handbook" 1972.
The file starts with a character sequence which appears as an arrow when punched on 8-hole paper tape.
0x08, 0x1C, 0x2A, 0x49, 0x08, 0x00
Then follows a byte count, encoded big-endian in the low 4 bits of the next 4 bytes. The high bits should be zero.
Then follows a 0xFF byte.
The data follows, as many bytes as specified in the header.
The trailer consists of the following bytes:
0x00, 0x00,
and then a 2-byte checksum (big-endian).
The alternate header sequence
0x08, 0x1C, 0x3E, 0x6B, 0x08, 0x00
is followed by an 8-nibble big-endian byte count.
Size Multiplier
In general, binary data will expand in sized very little when represented with this format.
EXAMPLE
Here is a hex dump of a formatted binary file containing the data "Hello, World!".
0000: 08 1C 2A 49 08 00 00 00 ..*I....
0008: 00 0E FF 48 65 6C 6C 6F ...Hello
0010: 2C 20 57 6F 72 6C 64 21 , World!
0018: 0A 00 00 04 73 ....s
COPYRIGHT
srec_cat version 1.58
Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011 Peter Miller
The srec_cat program comes with ABSOLUTELY NO WARRANTY; for details use the 'srec_cat -VERSion License' command. This is free software and
you are welcome to redistribute it under certain conditions; for details use the 'srec_cat -VERSion License' command.
AUTHOR
Peter Miller E-Mail: pmiller@opensource.org.au
//* WWW: http://miller.emu.id.au/pmiller/
Reference Manual SRecord srec_formatted_binary(5)