10-01-2014
Hi,
Without doubt, this is a mksysb scenario.
Regards
Dave
10 More Discussions You Might Find Interesting
1. AIX
Hi all,
We have a intermittent problem with printing from SAP running on AIX5.2 .
Version of Sap is 4.6b.
When a print is fired from SAP, the spool is created fine and then transferred to the host spool system (in this case the AIX Print queue). The problem seems to be happening when AIX... (3 Replies)
Discussion started by: pauldavi26
3 Replies
2. Solaris
I have a Sun Solaris 9 and I would like to clone the Operating System from a sun4u Sun Fire 480R machine to a Sun Fire 280R machine. The disk is the same size, the 480R has no space disk slot to the 280R disk for mirrioring, i have no external disk, I am not allowed to take the machine down.
... (1 Reply)
Discussion started by: hassan1
1 Replies
3. Solaris
I've got two drives in the same Sun server and I've been cloning the boot drive to the secondary drive by using both ufsdump/ufsrestore and the dd command sucessfully.
When I try and boot the cloned drive I get the following error:
WARNING - /usr/sbin/fsck not found. Most likely the mount... (10 Replies)
Discussion started by: johnj1965
10 Replies
4. AIX
Hello Everyone,
Can someone help me to mount a SAN hdisk which contains a clone data copy(san) of the remote server to the another machine. Both servers are running in AIX.
Thanks in advance !
Regards,
Gowtham.G (3 Replies)
Discussion started by: gowthamakanthan
3 Replies
5. IP Networking
Hello;
Please,I did the clone on virtualBox, but the machines have the same IP address: eth2 Link encap: Ethernet HWaddr 8:00:27: f0: 92:19 inet addr: 192.168.1.4 Bcast: 192.168.1.255 Mask: 255.255.255.0
how to change the address please?
Thank you so much (6 Replies)
Discussion started by: chercheur857
6 Replies
6. AIX
Hello,
I am trying to setup passwordless nophrase ssh between two machines for the user id: oraprod
here is what I did for a non-root user: oraprod
whoami:
oraprod
Machine A:
ssh-keygen -t dsa
cat ~/.ssh/id_rsa.pub
# GO TO MACHINE B
create (16 Replies)
Discussion started by: filosophizer
16 Replies
7. AIX
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Discussion started by: filosophizer
9 Replies
8. Red Hat
What is the best method to use to clone a Redhat machine, to ensure all software and config can be easily installed on new hardware?
Thank you! (3 Replies)
Discussion started by: da2013
3 Replies
9. AIX
Hello all,
I am trying to clone an entire aix 5.3 machine , not sure on the procedure.Can anyone help on what can be done ?Thanks (9 Replies)
Discussion started by: gull05
9 Replies
10. AIX
Hello to all,
Im having a new task in a new world (AIX - IBM Servers)
I have an IBM Server (Type - 9111-285 very old one) with one Hard disk (73 GB 10 K) with AIX 5.x, and I need to clone the existing disk to another with the same specifications.
Could you please give me some advice in order... (7 Replies)
Discussion started by: trevian3969
7 Replies
LEARN ABOUT ULTRIX
getnode
getnode(8) System Manager's Manual getnode(8)
Name
getnode - display one or more entries from the nodes database
Syntax
/etc/getnode [ node... ]
Description
For each given node argument, displays the corresponding node entry (or entries) from the nodes database. The nodes database is the one
used by DECnet. If you do not specify any node argument(s), all of the entries in the nodes database are displayed.
The node is either the node address or the node name for each node entry that you want to display. (Note that you can specify more than
one node argument in a single command.)
A node address is a decimal integer in the range of 1 to 1023 for single area networks, or has the format a.n for multiarea networks, where
a is the network area number (a decimal integer in the range of 2 to 63) and n is the node number (a decimal integer in the range of 1 to
1023).
A node name can be from 1 to 6 alphanumeric characters, including at least 1 alphabetic character.
Examples
# /etc/getnode 44.70 mynode <RET>
This command displays the entries in the nodes database for nodes 44.70 and mynode.
# /etc/getnode <RET>
This command displays all of the entries in the nodes database.
# /etc/getnode lttwi <RET>
This command displays the entry in the nodes database for node lttwi.
See Also
addnode(8), ccr(8), load(8), mop_mom(8), remnode(8), trigger(8)
Guide to Ethernet Communication Servers
getnode(8)