10-01-2014
Hi,
Without doubt, this is a mksysb scenario.
Regards
Dave
10 More Discussions You Might Find Interesting
1. AIX
Hi all,
We have a intermittent problem with printing from SAP running on AIX5.2 .
Version of Sap is 4.6b.
When a print is fired from SAP, the spool is created fine and then transferred to the host spool system (in this case the AIX Print queue). The problem seems to be happening when AIX... (3 Replies)
Discussion started by: pauldavi26
3 Replies
2. Solaris
I have a Sun Solaris 9 and I would like to clone the Operating System from a sun4u Sun Fire 480R machine to a Sun Fire 280R machine. The disk is the same size, the 480R has no space disk slot to the 280R disk for mirrioring, i have no external disk, I am not allowed to take the machine down.
... (1 Reply)
Discussion started by: hassan1
1 Replies
3. Solaris
I've got two drives in the same Sun server and I've been cloning the boot drive to the secondary drive by using both ufsdump/ufsrestore and the dd command sucessfully.
When I try and boot the cloned drive I get the following error:
WARNING - /usr/sbin/fsck not found. Most likely the mount... (10 Replies)
Discussion started by: johnj1965
10 Replies
4. AIX
Hello Everyone,
Can someone help me to mount a SAN hdisk which contains a clone data copy(san) of the remote server to the another machine. Both servers are running in AIX.
Thanks in advance !
Regards,
Gowtham.G (3 Replies)
Discussion started by: gowthamakanthan
3 Replies
5. IP Networking
Hello;
Please,I did the clone on virtualBox, but the machines have the same IP address: eth2 Link encap: Ethernet HWaddr 8:00:27: f0: 92:19 inet addr: 192.168.1.4 Bcast: 192.168.1.255 Mask: 255.255.255.0
how to change the address please?
Thank you so much (6 Replies)
Discussion started by: chercheur857
6 Replies
6. AIX
Hello,
I am trying to setup passwordless nophrase ssh between two machines for the user id: oraprod
here is what I did for a non-root user: oraprod
whoami:
oraprod
Machine A:
ssh-keygen -t dsa
cat ~/.ssh/id_rsa.pub
# GO TO MACHINE B
create (16 Replies)
Discussion started by: filosophizer
16 Replies
7. AIX
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Discussion started by: filosophizer
9 Replies
8. Red Hat
What is the best method to use to clone a Redhat machine, to ensure all software and config can be easily installed on new hardware?
Thank you! (3 Replies)
Discussion started by: da2013
3 Replies
9. AIX
Hello all,
I am trying to clone an entire aix 5.3 machine , not sure on the procedure.Can anyone help on what can be done ?Thanks (9 Replies)
Discussion started by: gull05
9 Replies
10. AIX
Hello to all,
Im having a new task in a new world (AIX - IBM Servers)
I have an IBM Server (Type - 9111-285 very old one) with one Hard disk (73 GB 10 K) with AIX 5.x, and I need to clone the existing disk to another with the same specifications.
Could you please give me some advice in order... (7 Replies)
Discussion started by: trevian3969
7 Replies
load(8) System Manager's Manual load(8)
Name
load - down-line load software to a target node
Syntax
/etc/load [ node ]
Description
The command loads software to an unattended target node. The target node is loaded by the host that executes the command.
The command requires the identification of the service circuit over which the load is performed, the Ethernet hardware address of the tar-
get node, and the service password needed to gain access to the target. This information is included in the nodes database entry for the
target node. A node entry is defined with the command. For further information, see The node is the name or address of the target node.
A node name consists of from one to six alphanumeric characters. For single networks, a node address consists of a decimal integer
(1-1023). For multiple networks, a node address consist of two decimal integers (n.n), where the first indicates the network number
(1-63), and the second indicates the node address (1-1023).
Options
-p Uses the specified service and password (next arguments) in accessing the target node. You can omit a target node's service and pass-
word from the nodes database for security reasons, but you must then specify the service and password in the command line by using the
option.
Examples
# /etc/load bangor -p 130fe
This command causes node to be loaded by the ULTRIX host node executing the command. The ULTRIX host uses the load files specified in the
nodes database entry for node to perform the load.
See Also
addnode(8), ccr(8), getnode(8), mop_mom(8), remnode(8), trigger(8)
Guide to Local Area Transport Servers
load(8)